Q1/ Convert each of the following data:1. 4.5 ft/sSI units (Km/h)U.S. Customary system of units (FPS)SI units kN/ m2. 1500 N.S3. 450 Ib/ft4. 1.94 slug/ft5. 45 MN/ 900 Gg.» SI unitskN°kg

Answered: Image /qna-images/answer/c3361900-6ef2-45dc-9f83-779acc70d4e4.jpg

Answered: Q1/ Convert each of the following data:…

Q1/ Convert each of the following data: 1. 4.5 ft/s SI units (Km/h) U.S. Customary system of units (FPS) SI units kN/ m³ SI units 2. 1500 N.S 3. 450 Ib/ft 4. 1.94 slug/ft 5. 45 MN/900 Gg. → kN°kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) Reproduce the following data given in Table 1 into new units. Table 1 Conversion of unit Old unit New unit 3.35 MJ/h 50 gal/lbm 25 newtons weight 0.85 kg.m/min? Btu/year (1 year = 365 days) I unit Mass in kg American Engineering unit -251 kJ/mol caИb-mol b) A fluid is used to characterize the degree of mixing in a continuous stirred tank. The fluid concentration in the outlet, C (kg/m³) is given as: 20 -exp' (-30t/V) C=- V Where V = volume in m and t= time in min. Express the units of 20 and 30, find the concentration in kg/m³ if given V and t are 1x10' cm³ and 200 s respectively and finally convert the equation so that all variables can be stated in CGS unit.
Water flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--
16000 1.440 14000 1.435 12000 1.430 10000 1.425 8000 1.420 6000 1.415 4000 1.410 2000 1.405 1.400 45 15 20 25 30 35 40 Temperature ["C] +dynamic viscosity (mPas] + density (gicm") Figure 1 (a) As shown in Figure 1, viscosity and density of honey was found to decrease with increase in temperature. Explain the reasons behind these phenomenon related to Fluid Mechanics in microscopic view. Dynamic viscolsty [mPa.s] Density [g/cm³]
1.18 Express the following in SI units: (a) 100 cfm (ft /min) (b) 5 gal (c) 65 mph (d) 5.4 acres
Use the provided data wherever you need. (transmitted power 0.050 MW, speed 500 rpm, Modulus of Elasticity 220 GPa, Modulus of Rigidity 70 GPa, Ultimate stress 620 MPa, Compression stress = 240 MPa, Yield stress 440 MPa, Shear stress = 120 MPa, F.S. = 4, Bending moment = 0.5 KN m, diameter of rivet = 10 mm, pitch = 50 mm)). Q1. Design the key that is used to connect a shaft with a hub as shown in figure. 1. If the diameter of the shaft is 60 mm. Check the whole system. Figure 1
9. A water Reservoir 80m 40m f 0.005 d = 0.2m Datum C D Turbine/generator Data: v in pipe = 3 m/s v at D = 0 Pressure at D = 0 Turbine efficiency = 80% Generator efficiency = 90% a). Pressure at C[+351.5 kN/m²] b). Output power from generator [24.16 kW] Determine:
QUESTION 3 A 7.62 mm caliber bullet travel in two different medium of gas of helium and nitrogen at constant speed of 1,548 miles per hour. The properties of the gas are given in Table 1. Cp (kJ/kg.K) Cv (kJ/kg.K) Temperature (K) Pressure (kPa) Table 1 Helium 5.192 3.115 300 unknown Nitrogen 1.039 0.746 300 unknown a) Calculate the speed of sound in both medium (helium and nitrogen). b) Determine the March number of the bullet for both medium. c) Do you think that the shockwave occurs in this bullet travel for both medium of gas? Sketch your ideas of this bullet travel and the shock wave (if available).
l .ll O 92 15:25 moodle.nct.edu.om/mod/ 11 P Flag question Calculate the density, weight density, specific mass of two liters of a fluid of weighs 5 kg (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) density of fluid (unit in kg/m3) : %3D weight density of fluid is (Unit in N/m³) specific mass (unit in m3/kg) = specific gravity = Question 8 Not yet answered
5. Consider a Pitot probe in high-speed flow.(c) You are flying through air at static p∞ = 0.8 atm [abs]. Your velocimeter broke,but you are still receiving the following direct stagnation pressure readings (atm[abs]) from the Pitot probe mounted on your aircraft’s noise: i) 3.152 ii) 1.357 iii) 38.428 iv) 0.8 Find the freestream Mach number corresponding to each of the pressure readings. (d) If we are to believe reading (iv), can we step out of the aircraft safely? Why?
Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (μ), and the density of the fluid (p). Using the dimensionless analysis, find the 7-groups for this case study.
Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (μ), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.
Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (4), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.