Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B. 36N/M 2m 1m A Im 2m 36N/M

Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B. 36N/M 2m 1m A Im 2m 36N/M

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a.…

A: Given : The diameter of hole, D = 40 mm The allowable normal stress = 60 MPa The allowable shear…

Q: d= 1.50 in. t=0.875 in. P= 7300 lb What is the average bearing stress produced in the support…

Q: The system is initially unstressed but the right support is moved 3 mm to the right whereas the left…

Q: 6 m A= 180 mm 6 m 4 m B.

Q: A, - 600 mm L = 400 mm 4, = 300 mm? L = 200 mm 4 =12 10 1 az = 23 10 E - 210 GPa E, - 70 GPa a) P=…

Q: PI-12 Fig.P1-12 shows an aluminum rođ ABC consisting of two portions AB and BC rigidly joined at B.…

A: Given data:

Q: The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3.…

Q: Q2-A reinforced concrete column of 250mm x 250mm cross section is designed to carry an axial…

Q: 1.25 The piece of wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the…

A: Given data: The area of a cross section of wood, A = 100 mm by 100 mm. The stress for tension, σt =…

Q: Q-1 Compute the max load (P) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A…

A: for the given bar σsteel = 120 MPa σbronze= 70 MPa To determine maximum load (P)

Q: 1- Calculate the axial deformation of point C and D? (D=36mm) t. 1A 2M steel E=200G pa Bras E= 105…

A: Given: Esteel=200 GPaEBrass=105 GPaD=36 mm

Q: Homework :-in the figure shown. Find the total deformation and the stress in each section if E is…

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

Q: 36. A mild steel bar is 40cm long. The lengths of parts of AB and BC of bar 20cm each. It is loaded…

Q: Ql: A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

Q: Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm…

Q: Q2) The lower ends of the three steel rods shown in (FIG. Q2) are at the same level before the force…

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di = 37.5 Allowable stress of rod : σ=…

Q: 10 kN В B y 6 m

Q: Two are connected by a knuckle jont, as shown in Fig by a pin of 40 mm in diameter. If a pull of 120…

Q: 1. Three vertical rods AB, CD, and EF supports s load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A: The stress in the cable is 12782.082 psi.

Q: 3- A Compound bar composed of three bar as shown .Determine the stress if the temperature change…

A: Calculated stress in brass and aluminum block when it compounded.

Q: -28 The steel pipe column shown in Fig. P2-28a has an out- side diameter of 150 mm and a wall…

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

Q: A horizontal force P= 110,976 N is pushing an inverted L-frame supported by a foundation at the…

Q: A1 A uniform bar of length L and cross sectional area A is held vertically at the upper end and…

A: When a uniform bar is hanged hanged vertically, the weight of bar varies from zero to W. At tip, it…

Q: The assembly shown consists of a light rigid bar AB, pinned at 0, that is attached to the steel and…

Q: A rod is composed of three segments as shown and carries the axial loads P1=120 kN and P2=50 kN as…

Q: Determine the stress in member KE for the truss loaded and supported as shown in figure (2). Note…

A: Truss is a structure which consists of many members and these members are pin jointed so that the…

Q: Q2- A steel pipe assembly supports a concentrated load of P = 22 kN as shown in Fig. 2. The outside…

Q: The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It…

Q: The compound steel bar shown in Fig. Q1(b) made of three uniform segments marked as 1, 2 and 3 of…

Q: Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: 1. Three vertical rods AB, CD, and EF supports a load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: To determine the stress in each segment.

Q: cross section, side length b, and wall thickness t. The second is a round of diameter b and wa…

Q: The c-clamp shown here has a solid, 2-cm- 10 cm diameter, circular cross-section. When it is…

A: The cross sectional diameter of the clamp is given as d=2 cm=20 mm. Using the diameter, find the…

Q: A joint is made by gluing two plywood gussets of thickness t = 0.78 in to wood boards. Determine the…

Q: III. A post tapers uniformly from a diameter at the upper end to a larger diameter D at the lower…

A: Upper area is minimum which should be considered.

Q: A key with a length of 7.5 times its thickness is subjected to a compressive force of 75 kN.…

Q: Q1A 30 cm square steel bearing plate lies between a 20 cm diameter wooden post and a concrete…

A: According to the given information:…

Q: 30° P 10 in. B 12 in.

A: Apply Equilibrium Conditions to above fbd

Q: The bar ABCD in Fig. (a) consists of three cylindrical steel segments with different lengths and…

Q: Try One - scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN,…

A: Calculated force component perpendicular N and parallel V to a - a inclined surface area. And also…

Q: The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: he turnbuckles in the diagram shown are tightened until the compression block DB exerts a force of…

A: To find stress in BD,CD

Q: The assembly in the depicted image below consists of a light rigid bar AB, pinned at O, that is…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the
allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar
is (10 mm) what is the bearing stress on bar AB.
Fig 1
B
36N/M
2m
36N/M
1m
pia veppt
2m
Im

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B 36N/M 2m 36N/M 1m 2m Im
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .if the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 36N M 2m 1m Im 2m