Q1 The block diagram of antenna pointing system with feedback is shown as in Figu The antenna will rotate clockwise and anti-clockwise until the desired angle posit achieved. The Vi, is input voltage that represents desired angle of antenna positio Whereas Vo is output voltage that represents actual angle of antenna position, 8o. 180 Error detector V-V-V CONTROLLER AMPLIFIER MOTOR Input E Based on Figure Q1: Output (Vo) 00 180° V V Output POTENTIOMETER sensor Figure Q1 (a) Classify the system control architecture. (b) Identify the function of potentiometer. (c) Discuss what will happens if the potentiometer is missing. (d) Identify the action taken by the controller if: (i) (ii) Vi=Vo Vi-Vo=0 (iii) Vi #Vo (iv) Vi - Vo>0 (v) Vi - Vo<0

Q1 The block diagram of antenna pointing system with feedback is shown as in Figu The antenna will rotate clockwise and anti-clockwise until the desired angle posit achieved. The Vi, is input voltage that represents desired angle of antenna positio Whereas Vo is output voltage that represents actual angle of antenna position, 8o. 180 Error detector V-V-V CONTROLLER AMPLIFIER MOTOR Input E Based on Figure Q1: Output (Vo) 00 180° V V Output POTENTIOMETER sensor Figure Q1 (a) Classify the system control architecture. (b) Identify the function of potentiometer. (c) Discuss what will happens if the potentiometer is missing. (d) Identify the action taken by the controller if: (i) (ii) Vi=Vo Vi-Vo=0 (iii) Vi #Vo (iv) Vi - Vo>0 (v) Vi - Vo<0

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem ECSQ

See similar textbooks

Similar questions

The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. If the peak voltage level of modulating and 1v and signal respectively, determine the modulating index. the carrier are 2V 2 1.5 1 0.5 -0.5 -1 -1.5 -2 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
Figure (1) shows the block diagram of a wideband frequency modulator using the indirect method. This modulator is used to transmit audio signals containing frequencies in the range of 100 Hz to 15 kHz. The narrowband is supplied with a carrier of frequency fl-0.1 MHz by crystal- controlled oscillator also ß-0.2, a second crystal- controlled oscillator supplied a sinusoidal wave of frequency 9.5 MHz to the mixer. The system Carrier frequency at the transmitter output, fc-100MHz Minimum frequency deviation, Af-75, find nl and n2? f(t) NBFM Freq. Multiplier 1 Oscillator1 Fig. (1) Mixer Oscillator2 Freq. Multiplier 2 frm(t) n1=72, n2=47 O n1=73, n2-48 O n1=75, n2=50 n1=77, n2=52 O n1=76, n2=51 O
Good day! Please help me understand how series modulator work in obtaining AM wave. Explain the flow of the circuit as well as the functions of the components. Need ASAP. Thank you so much!
Facts A clipper is an electronic circuit that produces an output by removing a part of the input above or below a reference value. That means the output of a clipper will be the same as that of the input other than the clipped part. Due to this, the peak to peak amplitude of the output of a clipper will be always less than that of the input. The main advantage of clippers is that they eliminate the unwanted noise present in the amplitude of an ac signal. Question: What do you think is the main disadvantage of a Clipper circuit over a Clamper Circuit?
it is the fractional value of an AC quantity through which the .6 * .AC quantity has advanced or delayed from the reference point frequency period Peak-to-peak value Phase different phase O
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
drive a formula for (SNR) of sinusoidal signal has been sampled and quantized.
Q14. What is the effect of value of filter capacitor on ripple voltage?
Note : the average value of asine - wave is always is (zero) Prove why?
Q#3 : How transient stability limit can be increased?
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
Draw a block diagram of a PM demodulator using frequency discriminator method.