Q2 A belt 100 mm wide and 10 mm thick is transmitting power at 1000 metres/min. The net driving tension is 1.8 times the tension on the slack side. If the safe permissible stress on the belt section in 1.6 MPa, calculate the maximum power, that can be transmitted at this speed. Assume density of the leather as 1000 kg/m3. Calculate the absolute maximum power that can be transmitted by this belt and the speed at which this can be transmitted.

Q2 A belt 100 mm wide and 10 mm thick is transmitting power at 1000 metres/min. The net driving tension is 1.8 times the tension on the slack side. If the safe permissible stress on the belt section in 1.6 MPa, calculate the maximum power, that can be transmitted at this speed. Assume density of the leather as 1000 kg/m3. Calculate the absolute maximum power that can be transmitted by this belt and the speed at which this can be transmitted.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 1650 and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted. 1 Add file
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
Q A shaft rotating at 200 r.p.m. drives another shaft at 300 r.p.m. and transmits 6 kW through a belt. The belt is 100 mm wide and 10 mm thick. The distance between the shafts is 4m. The smaller pulley is 0.5 m in diameter. Calculate the stress in the belt, if it is . An open belt drive, and 2. A cross belt drive. (Take μ = 0.3)
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
A workshop crane is lifting a load of 28 kN through a wire rope and a hook. The weight of the hook etc is 15 kN. The rope drum diameter may be taken as 30 times the diameter of the rope. The load is to be lifted with an acceleration of 1.2 m/sec2. Take a factor of safety of 6 and Young's modulus for the wire rope is 80 kN/mm2. The ultimate stress may be taken as 1800 MPa. The cross-sectional area of the rope may be taken as 0.38 times the square of the wire rope diameter. Neglect the effect of impact load. Calculate the diameter of the wire rope.
If the difference between tight and slack side for a leather belting doesnot exceed 100 N/cm of width for a belt 0.5 cm thick. Find the maximum stress in the belt. Consider. angle of lap = 170° Belt speed %3D 1000 m/min %3D density of leather = 10-3 kg/cm³ Coefficient of friction 0.25 %3D
Design a suitable wire rope to lift a load of 13 kN of debris from a well 70 m deep. The rope should have a factor of safety equal to 6. The weight of the bucket is 7.5 kN. The load is lifted with a maximum speed of 150 m/min which is attained in 1 second. Find also the stress induced in the rope due to starting with an initial slack of 250 mm. The average tensile strength of the rope may be taken as 590 d2 Newtons (where d is the rope diameter in mm) for 6 x 19 wire rope. The weight of the rope is 18.5 N/m. Take the diameter of the wire (dw) = 0.063d and area of rope A = 0.38 d2.
@ ll 65% 1:20 PM Edit 18 TREBLA Questian B2 The hydraulic cylinder shown in figure B2a exerts a force of 3 kN drected to the right on point Band to the left on point E. If the drum is required to rotate dockwise at a constant speed a. Copy and complete the free body diagram (figure B2b) by supplying the missing forces, moments, labels and dimensions. b. Detemine the magnitude of the couple M required to rotate the drum dockwise at a constant speed [5 marks] [10 marks) H,=0.40 H-0.30 D. 150'mm 150 mm E 300 mm 300 mm 150 mm 150 mm 250 mm Figure B2a 150 mm 300 mm 150 mm Figure B2b DO פם B8 W Tools Mobile View Share PDF to DOC 3
Q1/ An open belt drive connected two pulleys 120 cm and 50 cm diameter on parallel shafts 4 m apart. The belt weights 0.9 kg/m length and maximum tension in it is not to exceed 2000 N. 0.3. The 120 cm pulley, which is the driver, runs at 200 rpm. Due to belt slip on one of the pulleys, the velocity of the driven shaft is only 450 rpm. Calculate the torque on each of the two shafts and power transmitted.
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.
An extra flexible 8 x 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 80 kN of load. The weight of the rope is 36 kN. The maximum speed is 3 m/s and the acceleration is 1.6 m/s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84,000 MPa. Determine the effective load during acceleration. Express your final answer in kN and use ONE decimal place. Write only the numerical value and do not type the unit anymore.
The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack