Q2 (a) Figure Q1(a) Analogue to Digital Converters (ADCs) are used to change analogue signals to digital signals. In general, the conversion process is based on four main steps. (1) Select any two of the conversion steps and explain the nature of the input signal based on time and amplitude for the two steps. Briefly discuss the quality of the ADC output if we increase the resolution of the signal plots as shown in Figure Q2(a). quantization Figure Q2(a) There are five different types of ADCs packaged as integrated circuits for use in electronic systems. List the names of any two of them. limital signals to continuous analogue

Q2 (a) Figure Q1(a) Analogue to Digital Converters (ADCs) are used to change analogue signals to digital signals. In general, the conversion process is based on four main steps. (1) Select any two of the conversion steps and explain the nature of the input signal based on time and amplitude for the two steps. Briefly discuss the quality of the ADC output if we increase the resolution of the signal plots as shown in Figure Q2(a). quantization Figure Q2(a) There are five different types of ADCs packaged as integrated circuits for use in electronic systems. List the names of any two of them. limital signals to continuous analogue

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1/ Sketch and describe mathematically the even and odd components of the signal shown in Figure (1) -1-2-012345 Figure (1)
What is: Nyquist criterion margins
Q3. Design a DC/DC buck converter (as shown in Figure Q3) for an input voltage of 12V and an output of 5V at 20A. Assume a switching frequency of 10kHz. Constrain the inductor ripple current to be 10% of the input current and limit the output voltage ripple to 50mVp-p. a) Explain the working mechanism of the converter by sketching equivalent circuit diagrams when the switch Q is ON and OFF, Calculate the duty cycle of the switch. Find the ripple of the inductor current. Calculate the required inductance and capacitance. Sketch the waveform of the output voltage. Is the converter works at continuous conduction mode CCM? If so, give proof of that b) c) d) e) f) g) If the load current varies between 0 and 2A, what is the value of the duty cycle range and at what operating condition? DA L C² Figure Q3 DC/DC buck converter. R
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
Figure shown below represents a circuit combining a positive limiter with a negative limiter. Determine the output voltage waveform.
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
The data-input and data-select waveforms in Figure 7 are applied to the multiplexer. Determine the output waveform F in relation to the inputs.
the way of working for boost dc-to-dc converter.
Signal and system plz explain every step that how do this
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.
-4) Design a circait containing a comparater with a hy steresis loop a. Draw the circuit with all values of the components required for the dksign. b. What is the name of the circuit in (a). c. Sketch the output waveform when the input is a 15-V peak sine wave. d. Adjust the value of RI in the circuit such that the hysteresis width will be 10.