Q2: The armature and field resistance of a 220 V DC series motor is 0.15 ohm and 0.1 ohm respectively. It runs at a speed of 1000 rpm when connected to rated voltage drawing a current of 30 A. If an external resistance of 1 ohm is inserted in series with the motor, calculate the new steady state armature current and the speed. Assume the torque is proportional to the square of the speed (To N)

Q2: The armature and field resistance of a 220 V DC series motor is 0.15 ohm and 0.1 ohm respectively. It runs at a speed of 1000 rpm when connected to rated voltage drawing a current of 30 A. If an external resistance of 1 ohm is inserted in series with the motor, calculate the new steady state armature current and the speed. Assume the torque is proportional to the square of the speed (To N)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
2. A 2-pole, 50 Hz induction motor supplies 15 kW to a load at a speed of 2950 rpm. a. What is the motor's slip? b. What is the induced torque in the motor in N-m under these conditions? c. What will be the operating speed of the motor be if its torque is doubled? d. How much power will be supplied by the motor when the torque is doubled?
A 230v DC series motor takes 30A when giving its rated output at 1400 rpm. It has a field resistance of 0,4 ohms, Calculate the value of the resistance (Ra) of the armature when Eb = 200V. Select the correct response: 0.2 ohms 0.6 ohms 0.8 ohms 0.4 ohms
200 +21. If maximum torque of an induction motor is kg-m at a slip of 12%, the torque at 6% slip would be...... kg-m. 1 (a) 100 (b) 160 (c) 50 (d) 40 B, 1993)
A 22 kW, 230 V Series DC motor runs at 750 rev/min at full load and draws 110 A from the supply. The resistance of the armature is 0.1250 and the series field 0.0250. Calculate the speed when the load is reduced such that the input current reduces to 56 A. Assume that the useful flux per pole at 110 A is 23.9 mWb and the flux for 56 A is be 15.5 mWb.
6. The motion in DC motor can be increased by the following factors... (you may choose more than one) * a) Using a stronger magnet b) Increasing the potential difference c) Increasing the current d) Increasing the number of turns on the coil
A• universal series motor has a resistance of 30 and an inductance of X Henry. when connected to a 250 V dc supply and loaded to take .0.8 A it runs at 2000 rpm Determine the value of X if the power factor is 0.6, when connected to a 250 V, 50 Hz ac supply and loaded to take the 1A,then find the torque
Q4/B/ What are the principal characteristics of a series DC motor? What are its uses? Core Mc
A 230 V dc series motor has an armature resistance of 0.2 ohm and field resistance of 0.1 ohm at rated voltage. The motor draws a line current of 40 amperes and runs at a speed of 1000 rpm. Find speed of the motor for line current of 20 A at 230 V. Assume that flux at 20 A line current is 60% of flux at 40 A line current.
An induction motor has a full load slip of 0.04. It's starting current 5 times its full load current. What is the ratio of starting torque to the full load torque? Select one: a. 2 b. 0.5 c. 0.2 d. 1
(7) The only parts suffers from eddy currents in AC motors: a- The stator. b- The rotor. c- The stator and rotor. (8) The unit of torque is a- W (rad. s') b- Js -1 C- Nm
Example : A universal series motor has a resistance of 30 and an inductance of 0.5 H. when connected to a 250 V dc supply and loaded to take 0.8 A it runs at 2000 rpm. Determine the speed, torque and power factor, when connected to a 250 V, 50 Hz ac supply and loaded to take the same current.