Q2 : The daily demands of three consumers are given below. Plot the load curve and find (i) maximum demand of individual consumer (ii) load factor of individual consumer (iii) diversity factor and (iv) load factor of the station. (v) daily requirement if the calorific value of oil used were (9,000 kcal/kg) and the average heat rate of station were (2680 kcal/kWh). Time 12AM – 6AM 6AM -1 PM 1PM-5 РМ 5 PМ-9 РМ 9 PM – 12 AM Consumer 1 80 W 400 W 1500 W 600 W No-load Consumer 2 No-load 350 W 800 W 1000 W 300 W Consumer 3 50 W 110 W 1100 W 900 W 150 W

Q2 : The daily demands of three consumers are given below. Plot the load curve and find (i) maximum demand of individual consumer (ii) load factor of individual consumer (iii) diversity factor and (iv) load factor of the station. (v) daily requirement if the calorific value of oil used were (9,000 kcal/kg) and the average heat rate of station were (2680 kcal/kWh). Time 12AM – 6AM 6AM -1 PM 1PM-5 РМ 5 PМ-9 РМ 9 PM – 12 AM Consumer 1 80 W 400 W 1500 W 600 W No-load Consumer 2 No-load 350 W 800 W 1000 W 300 W Consumer 3 50 W 110 W 1100 W 900 W 150 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
A power station is to supply two loads. The daily load curve of the station is as shown in figure below. If the load factor of the two loads are 0.416 and 0.458 respectively, and the diversity factor of the power station is 1.142, find:1- The load factor of power station.2- The energy consumed per day and the maximum demand(connected load) of each load.
A power station is to supply four regions of loads whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station.
step down chopper has Vs = 230 V and R = 10 0. For a duty cycle of 0.4, the power taken by the chopper is 2097 Watts. Find the chopper efficiency. Take the voltage drop across the chopper switch as 2 V. a) 98 % b) 89.96 % c) 99.14 % d) 96.54 %
Q2/ The following demands in a power plant as: Group 1:300 kW between 7 A.M. and 8 P.M Group 2: 150 kW between 5 A.M. and 9 A.M Group 3: 100 kw between 5 A.M and 4 P.M Group 4: 200 kw between 9 A.M and 4 P.M and then between 4 P.M and 5 A.M plot the daily load curve duration curve and Calculate 1- Units generating per day. 2-load factor 3-diversity factor?
A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source.If the voltage drop across the capacitor is 115 volts and the power taken by the circuitis 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) theline voltage, (d) the circuit power factor. draw the circuit diagram
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
A base load station having a capacity of 18 MW and a standby station having a capacity of 22 MW share a common load. Find the annual load factors and plant capacity factors of two power stations from the following data :Annual standby station output = 740OMWH Annual base load station output = 100000 M kWh Peak load on standby station = 12 MW Hours of use by standby station/year = 2200 hours
Q1 A power station is to supply two loads. The daily load curve of the station is as shown in figure below. If the load factor of the two loads are 0.416 and 0.458 respectively, and the diversity factor of the power station is 1.142, find: 1- The load factor of power station. 2- The energy consumed per day and the maximum demand (connected load) of each load. KW 1400 1200 1000 800 600 400 200 6 12 14 20 24 hours
8. Three generators are rated as follows: Gl: 100MVA, 33kv,Xg1 = 0.1pu. G2: 150MVA,32kv.xg1 0.08pu.G3:110MVA,30kv.xg1 = 0.12pu.Determine the reactance of the generator corresponding to base values of 200MVA and 35kv.
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
Problem 3 An electric table saw, a wood shaper, and a motor load of a workshop establish an 18 kVA power demand at 50 percent lagging power factor on a 220 V, 60 Hz supply. a) Establish the power triangle for the load. b) Determine the power-factor capacitor that must be place in parallel with the load to raise the power factor to 90 percent lagging.