Q2) When a body is removed from an oven, its temperature is measured at 210°F. Four minutes later its temperature is 100° F. If the room temperature is found to be 50°F,how long will it take for the chicken to cool off to a temperature of 70°F. What is the steady state temperature of the body? Clarify

Q2) When a body is removed from an oven, its temperature is measured at 210°F. Four minutes later its temperature is 100° F. If the room temperature is found to be 50°F,how long will it take for the chicken to cool off to a temperature of 70°F. What is the steady state temperature of the body? Clarify

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Similar questions

The Sahara desert with a very arid climate is one of the hottest regions in the world. Its average temperature is above 30°C or 86°F. In a 24-hour period, the temperature can go from a day-time high of 95°F to a low of 32°F at night. (a) By how many Celsius degrees does the temperature fall in the 24-hour period? °C (b) By how many Kelvin degrees does the temperature fall in the 24-hour period? K
4. When 435 J of heat is added to 3.4 g of olive oil at 21 C, the temperature increases to 85 C. What is the specific Heat of the olive oil?
3. According to Newton's cooling law, the rate of cooling of a hot body is pro- portional to the difference between the temperatures of the hot body and the environment. If the room temperature is 35°C and the temperature of a hot body in the room cools down to 55°C from 105°C Celsius in just 6 minutes, then how many more minutes will it take to cool down to 45°C?
THERMODYNAMICS PROBLEM 2. A closed tank of a certain gas receives heat from being exposed to the sun. The bourdon pressure gauge initially reads 20 kpa but after some time it reads 30 kpa. Find the final absolute pressure of the gas inside 3. From #2, the initial temperature of the gas is 10Cbut it rises to 30C after some time: Find the ff: A. initial and final temperatures in °F,?,????.B. the change in temperature in °C,°F,?,????
Q1: If a calorimeter is not assumed to be adiabatic, how would one calculate the heat transfer? Guide Questions: What are the parameters to be considered and the equations to be used? What law of thermodynamics does this transfer of heat to the surroundings touch? Is an adiabatic system automatically considered as a closed system? Please help me understand by also attaching a reference/book/journal article. This would help me in my essay. Thank you.
A thermometer is taken outside a room, where the ambient temperature is 5°F. After 1 minute, the thermometer reads 55°F, and after 5 minutes, 30°F. What was the initial temperature inside the room?
b) For an Otto Engine the temperature at the end of combustion is 280 K. If the temperature in the gas side and coolant side of the wall are 177 °C and 127 °C and cylinder wall thickness is 5 mm;
For the following table, fill in the missing values. Tparcel refers to the temperature of a single parcel being lifted from 0 – 5 km, whereas Tenvironment represents the environmental lapse rate. "e" is the yapour pressure and "es" is the saturation yapour pressure. The figure relating saturation yapour pressure and temperature can be found below. The dry adiabatic lapse rate is 10° C/km and the moist adiabatic lapse rate is constant and 6° C/km. Height Tenviornment Tparcel е (parcel) es (parcel) RH 0 km 20 ° C 20 ° C 6.0 mb 24 mb 1 km 12 ° C 10 ° C 50 % 2 km 4° C 6 mb 3 km -4 ° C 3 mb 4 km -12 ° C -12 ° C 2.5 mb 5 km -20 ° C 1.5 mb 100 %
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
A container whose temperature is kept at 200°C is located at 40 ft. above sea level. An object is placed in the said container with a temperature reading of 30°C. After 20 minutes the temperature of the object is 45°C. а. C and k b. General solution Find the temperature of the object after 30 minutes. What is object's temperature 10 minutes before the object reaches the temperature reading of 45°C? с. d.
Latent heat of fusion is the heat given up as a substance freezes. The latentheat of fusion for water is 144 British thermal units per pound (Btu/lb). Thismeans that 144 Btu are given up for each pound of water that freezes. Howmany British thermal units of heat are given up when 4,000 pounds of waterfreeze?
Air treated as an ideal gas and having a specific heat at constant volume Cv=1200 J/kg.K undergoes a process. During this process, heat is observed to exit the system with an amount of 10 kJ while work is provided to the system with an amount of 28 kJ. If the initial temperature of air was 20 C, what is the final temperature of air if the mass of air undergoing the process is 0.7 Kg. Select one: O a. 35.5 C O b. 52.4 C c. 41.4 C O d. 29.5 C