Q2. In a DSB-SC AM system, the carrier is e(t) = 0.5 cos (20000 nt) and the message signal is given by m() = sinc(t) Find and Sketch the frequency domain (spectram) representation of the modulated transmitted AM signal and show the bandwidth of the modulated AM signal. If the modulation scheme is: (a) DSB-TC (b) DSB-SC (c) SSB (d) VSB

Q2. In a DSB-SC AM system, the carrier is e(t) = 0.5 cos (20000 nt) and the message signal is given by m() = sinc(t) Find and Sketch the frequency domain (spectram) representation of the modulated transmitted AM signal and show the bandwidth of the modulated AM signal. If the modulation scheme is: (a) DSB-TC (b) DSB-SC (c) SSB (d) VSB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
S Answer the two following questions: A. A sinusoidally modulated AM waveform is shown below: Determine: (a) Peak amplitude of the upper and lower side frequencies. (b) Peak amplitude of the unmodulated carrier. (c) The modulation index. (d) The transmission efficiency. (e) The amplitude of the carrier which must be added or subtracted to attain a modulation index of 0.5. 16V 8V- -8V. -16V-
A carrier signal given by 10cos27x108t volt is FM modulated by single tone message 4cos27Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power.
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. 3.5V- 1V- a) What is the amplitude of the carrier signal? b) c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal What is the modulation index?
If the carrier signal is given as c(t)=5cos10000t, and the modulating signal is given as m (t) = 4e2rtthen the power (in watt) of the modulated DSB-SC signal is:
2 (AM) A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with modulation index 0.8. What is the amplitude of the carrier? What is the power of the side bands? What is the efficiency of the modulated signal?
IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. a) b) c) d) 5.5V- 2V What is the percentage of modulation? What is the amplitude of the carrier signal? To achieve 75 percent modulation, what amplitude of the modulating signal is needed? Calculate the effective voltage of the AM signal
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS
03: The output voltage of a transmitter is given by the following envelope wave form. This voltage is fed to a load (RL= 12). What is the name of the modulator that can be used to generate DSB-AM, and draw the block diagram of this modulator? Then find: (a) The carrier frequency and the message frequency. (b) The double side band frequencies (USB and LSB). (c) The modulation index. (d) The carrier power and power in sidebands. (e) The total power. (f) Write the modulated wave equation at the output of the transmitter. Amplitude 20 volts 40 volts 20 Acti JA see. Go to
Figure 1 shows the AM waveform envelope generated with a carrier frequency of 20 kHz and a modulating frequency of 1 kHz. 0.5 -0.5 -1.5 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Time, seconds x 10 Figure 1: Plot of AM Waveform. Determine: i) Modulation index. ii) Carrier signal equation. iii) Information signal equation. iv) Sketch the frequency spectrum of the AM signal. v) Bandwidth of the signal. vi) Total power of the signal, given the resistance is 50 2. AM Signal, V
The power of operating frequency in AM station is 145 W, and there is 89% modulation depth. (assuming single side band suppressed carrier). What is the power of the side bands?