Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel andaluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist morethan 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa,Ga 28 Gpa.AluminiumSteel75.mm100mm1m

Answered: Image /qna-images/answer/b7fa46cd-faf7-4076-aca8-9e376c7a175a.jpg

Q2:The composite torsion member as shown in Fig. If the allowable stress aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft than.1.45°, determine the maximum torque T that can be applied to the me Ga-28 Gpa.

Q2:The composite torsion member as shown in Fig. If the allowable stress aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft than.1.45°, determine the maximum torque T that can be applied to the me Ga-28 Gpa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q3-The assembly shown consists of an aluminum shell (Ea=8.6*10^6psi,xa=11.2 19^-6/F)fully bonded to…

Q: The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a.…

A: Given : The diameter of hole, D = 40 mm The allowable normal stress = 60 MPa The allowable shear…

Q: d= 1.50 in. t=0.875 in. P= 7300 lb What is the average bearing stress produced in the support…

Q: 2) Find the axial stresses of members BD, CD and CE. Strte if it is tensile or compressive. AM 3m 3w…

A: Let the reaction on support A and H are to be vertically upward. Take moment equilibrium at point A…

Q: The invariants of a stress system at any point are 1 = -2 MPa, I2 = -15 MPa and I3 = 0 MPa Find…

A: Given Data : Invariants of stress system are :σx=I1=-2 Mpaσy=I2=-15 Mpaζxy=I3=0 Mpa

Q: Q2-A reinforced concrete column of 250mm x 250mm cross section is designed to carry an axial…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

Q: Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of…

Q: The maximum value of the torsional shear stress is kpsi.

A: To find Torsional shear stress

Q: For the shown figure, determine the average normal stress (MPa) developed in rod BC if the load has…

Q: Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium. Brass and Steel,…

Q: The state of stress at a point in a member is shown on the element. Suppose that σx = -50 MPa , σy =…

A: σX=-50MPaσy=-120MPaζxy=-30MPa All stresses are compressive Formula for shear stresses:-…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of each…

A: The stress acting between two bodies when they are in contact to each other. It can be called as…

Q: 1. Three vertical rods AB, CD, and EF supports s load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Q2 Design the rectangular key which is located on the shaft motor if the diameter of it is (48) mm…

Q: 5) A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length…

A: Given: Diameter of the brass rod=8mmLength of the rod=0.4mWall thickness t=3mmInternal diameter of…

Q: A motor boat engine shaft is coupled to the propeller shaft of diameter 30mm. If the allowable shear…

A: Given, Allowable shear stress, τ=43 MPa=43 N/mm2 The diameter of the shaft, d=30 mm

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A: The stress in the cable is 12782.082 psi.

Q: -bar rigidly fixed at its both ends uniformly tapers from 90 er. What will be the maximum stress…

A: This explanation is given below

Q: 1 MPa 2- For the state of stress as shown below 2 MPa a) Find principal stresses З МРа b) Draw…

A: Given:σx=3 MPaσy=1 MPaζxy=2 MPa

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: Two solid cylindrical rods support a load of P = 32 kN as shown. Rod (1) has a diameter of 14 mm,…

Q: Q3 Design the square key which is located on the shaft motor if the diameter of it is (20) mm and…

A: d=20 mm σc=400Nmm2τs=200 Nmm2F=10000N or 10kN Now Mt=F×d2Mt=10000×.022Mt=100 Nm σc=4Mtdhlτs=2Mtbdl…

Q: A flanged bolt coupling consist of a 9 steel bolts evenly spaced around a bolt circle 300 mm in…

Q: The state of stress at a point under plane stress condi- tion is o = 20 MPа, о, = 50 MPa and t = 20…

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

Q: 2:The load (50 kN) applied on the rigid beam (AB) s supported by the pin (A) and two rods ,one made…

Q: Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer…

Q: 04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN)…

Q: 2.) Solve for the normal stress of rod AB with a diameter of 10mm if the block has a mass of 40kgC…

Q: pute the stress in a round bar having a diameter of 10.0 mm and subjected to le force of 3500 N.

Q: 2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the…

Q: The c-clamp shown here has a solid, 2-cm- 10 cm diameter, circular cross-section. When it is…

A: The cross sectional diameter of the clamp is given as d=2 cm=20 mm. Using the diameter, find the…

Q: and P₂ (KN) as shown. Analyze the system of axial bars if the allowable stress requirement and axial…

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has…

Q: Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of…

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what…

A: Given data

Q: 2. A shaft (30 mm )diameter is transmitting power at a maximum shear stress of (80 MPa). If a pulley…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: To find : determine the largest allowable value of P. Given :- diameter of shaft ds=30 mm shear…

Q: The rigid bar ACE is supported by two steel rods AB and CD (Esteet = 200 GPa) with the cross…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: QUESTION 3 Calculate for E=200 GPa: 3.1 The diameter 'd' if the stress is not to exceed 142 MPa 3.2…

A: As per given question we determine the value of D and x

Q: Mcq: the maximum shar stress in contact between steel spheres pressed together lies? 1-at the…

A: Ans: 3 is correct. Under the contact surface

Q: Q2- The homogeneous bar AB have diameters ubjected to an axial tensile load of 25KN. have he new…

A: SOM Note: Working stress should be 0.25 N/mm2

Q: Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer…

A: Calculated the smallest thickness of shaft.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel and
aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist more
than 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa,
Ga 28 Gpa.
Aluminium
Steel
75
.mm
100
mm
1m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
1. State three underlying assumptions in the formulation of the torsion formula, .TG Jrl == 2 Determine the torsional rigidity of a 300 mm long steel shaft with a diameter of 50 mm. (G = 80 GPa). 3. A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. The maximum allowable shear stress is 50 MPa and the maximum torque to be transmitted by the shaft is 30 % greater than the mean torque. The internal diameter of the shaft is 50 % that of the external diameter. Calculate the shaft dimensions and the angle of twist of the shaft over 3 m when transmitting the above torque (G = 80 GPa).
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
2: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m
3) A 10 kN-m torque, T, and a 50 kN axial load, F, are applied to the end of an aluminum 6063 tank containing compressed air under a pressure of 2 MPa. The tank has a 400 mm outer diameter and a 20 mm wall thickness. Aluminum 6063 has a yield strength of 48 MPa. a. Draw and label a stress element for the most stressed point on the tank. Explain why this is the most stressed point. b. Sketch Mohr's circle and find the principal stresses at the most stressed point. Make sure you label your axes! c. Determine whether or not this is a safe loading scenario by considering the max normal stress, max shear stress, and distortion energy. (Hint - calculate the factor of safety for each failure criteria) T
the Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel are (allow)mg = 45MPa and (allow)st=84 MPa, respectively. the shear modulus of elasticity for Am1004-T61 magnesium alloy is 18 GPa and for A-36 steel is 75 GPa determine the maximum allowable torque that can be applied to A (see attached jpg file) find the corresponding angle of twist of end A
A)The maximum stress in a section of a circular tube subject to a torque is τmax = 37 MPa . If the inner diameter is Di = 4.25 cm and the outer diameter is Do= 5.25 cm , what is the torque on the section?
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at 4, and a torque of T= 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %D 2 m 100 mm 50 mm T= 50 kN. m