Q4/ A Porter governor has arms 250 mm long. The upper arms are pivoted on the axis of rotation and the lower arms are attached to a sleeve at a distance of 30 mm from the axis. Each ball has a weight of 20 N and the weight of the load on the sleeve is 200 N. If the radius of rotation of the balls at a speed of 260 rpm is 100 mm, find the speed of the governor after the sleeve has lifted 50 mm.

Q4/ A Porter governor has arms 250 mm long. The upper arms are pivoted on the axis of rotation and the lower arms are attached to a sleeve at a distance of 30 mm from the axis. Each ball has a weight of 20 N and the weight of the load on the sleeve is 200 N. If the radius of rotation of the balls at a speed of 260 rpm is 100 mm, find the speed of the governor after the sleeve has lifted 50 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel weights 592 kg with a diameter 1.4 m. The flywheel rotates at 979 revolution per minute (rpm). If a constant braking torque 522 N.m is applied to the shaft during the rotation, calculate the number of revolutions turned through before the flywheel is coming to a complete stop.
A rod ABC rotating at 20rpm about a vertical axisthrough point A supports a 400N ball at its lower end. Itis fixed in position by the rod BD as shown in the figure.Neglecting the weights of rods AC and BD, compute theforce P in rod BD. Identify if this force is in tension orcompression. At what rpm will this force be zero? DrawFBD of the rod AC during the motion of the system.
A constant torque of 2kN-m is exerted on a crankshaft to start the engine.The flywheel has a mass of 1800kg and a radius of gyration 1m .If there is a resisting torque of 1kN-m,find the speed of the engine after 1 minute.
Consider the system shown at right. Find an equation of motion for the block with mass m,. Assume that the small wheel has negligible mass moment of inertia and that the larger one has a radius R and a mass moment of inertia I (measured respect to its axis of rotation). Note that there is a friction between the block with m2 mass m2 and the plane. The dynamic friction coefficient is equal to µa. m1 Md
The EOM for the following 1-DOF gyroscope is: JÖ + BO + KO = Hw w is the angular velocity of the gyroscope about the input axis, is the angular position of the spin axis, H is the angular momentum stored in the spinning wheel, J is the mass moment of inertia of the wheel about the output axis, B is the viscous friction coefficient about the output axis, and K is the spring constant of the restraining spring attached to the spin axis. Determine the transfer function relating output to the input w. Case K spin axis output axis BOD Go Wheel spins at constant velocity input axis
Determine the following : (a) Tension in each cable when at the bottom (b) the minimum angular velocity in rpm to sustain themotion (refer to the image below)
4. A loaded governor of the Porter type has equal arms and links each 250 mm long. The mass of each ball is 2 kg and the central mass is 12 kg. When the ball radius is 150 mm, the valve is fully open and when the radius is 185 mm, the valve is closed. Find the maximum speed and the range of speed. If the maximum speed is to be increased 20% by an addition of mass to the central load, find what additional mass is required. [Ans. 193 r.p.m.; 16 r.p.m.; 6.14 kg]
* F2 # 3 E Problem 4. EOM Derivation Derive the equation of motion for the following system: We want to measure the spin rate w of the rotating shaft of a turbine. To do it we push a small mass m against the end of the shaft. The shaft makes friction contact with the drag cup mounted on the mass. The frictional torque is b (w). Assume that the rotational spring torque is ke and that the moment of inertia of mass m is J. J Rotating Shaft F3 @ $ 4 R b J, m Drag Cup F4 Q Search % 5 F5 T 0 Wall * A 6 F6 Y 2 * F7 & 7 PrtScn U F8 4 8 Home 6. F9 9 End F10 Po 0
Consider a pulley system shown below. The coordinate x is the displacement of G. Assume there is no slip between the cord and the pulley, and disk and the ground. What is the kinetic energy of the system? Select all that apply. I don't know how to get these answers.
Find the equations of motion for a lever of length 2a and of mass M rotating around its tip A 20
4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
The 10 N cylinder moves in a frictionless pipe. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. (d is the distance from the right end of the arc k2). The system rotates around a fixed z-axis. Find the constant velocity of the cylinder for d = 0.20 m?