Q4-A vertical cylinder tank with diameter of 12m and depth of 4m is filled to the top with water at 20C°. If the water is heated to 100C°, how much water is spilled over, and what is the percentage in mass reduction. (at 20C° density=998Kg/m3, at 100C° density%3D958KG/m3).

Q4-A vertical cylinder tank with diameter of 12m and depth of 4m is filled to the top with water at 20C°. If the water is heated to 100C°, how much water is spilled over, and what is the percentage in mass reduction. (at 20C° density=998Kg/m3, at 100C° density%3D958KG/m3).

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Related questions

Q: A cylinder 1.00 m tall with inside diameter 0.120 m is used to hold propane gas (molar mass 44.1…

Q: If given the option between using a P1000 and a P200 pipetter to dispense 200 uL, the P200 should be…

A: P1000 pipette measure between 200μl to 1000μl And P200 pipette measure upto 200μl

Q: Feed gas containing of 78.5mol % H₂, 21% of N₂ & 0.5% of Ar is mixed with recycle gas and enters a…

A: NH3 is produced by Heber's cycle. Material balance method used here.

Q: A chart is prepared by plotting In Ksp versus 1/T, using data obtained by performing a lab…

A: We have plot of lnKsp vs 1/T with equation of line as y = (-5.0020x10^3)x+(2.100x10^1) . We have to…

Q: Fine aggregate sample was tested to find its physical properties. The test results were as follows:…

A: Given data: Bulk specific gravity is G=2.45 Apparent specific gravity is Gm=2.5 Mass of vessel full…

Q: .40. Ammonia is burned to form nitric oxide in the following reaction: 4NH3 + 502 - 4NO + 6H2O (a)…

Q: A solution containing 100 lbm KNO 3/100 lbm H 2O at 80°C is fed to a cooling crystallizer operated…

Q: 0 A foo Rmal/h stream that is 97 msle % Carbon betrachlorice Cccl4) and 3 % Carbon disulfide ccs) is…

Q: Q7. Choose suitable equipment and streams in plan flowshcet to produce benzoic acid from toluene…

A: This process is carried out by oxidation of toluene.

Q: ride it related eliter of water, Intions output? outeut? -cl=35-5

A: Given : volume (4L) this focus (0.02 M) from sodium chloride (NaCl) it was relaxed by adding one…

Q: 4. A flash chamber operating at 50 °C and 200 kPa is separating 1,000 kg moles/hr of a feed that is…

A: Solution

Q: In a single effect evaporator, steam economy is equal to 0.95. If this evaporator for operation…

A: The economy of an evaporator is based on steam needed and water vapor generated as follows:…

Q: A single effect evaporator is used to concentrate 10 000 kg / hr of tomato juice from 5% total…

Q: A liquid stream flowing at 100 g/min contains 0.3 mole fraction benzene (Mw=78) and the balance 0.7…

A: Given data mass flow rate of stream = 100 g/min mole fraction of benzene in stream Xb = 0.3 mole…

Q: 1. A labelled flowchart of a continuous steady-state two-unit process is shown below. Each stream…

A: A labelled flowchart of the steady state process is given. The mass flow rate of inlet stream is 100…

Q: Suppose you have an initial chlorine concentration of 5%. Then out of that, you are told to prepare…

Q: EXAmple 2: tookultha of amrsture Contalning l0,20,30 and Homl of Propanezn-butanesn-Pentanesand…

Q: 1100 kg/h of a mixture containing equal parts by mass of methanol and water is distilled. Product…

Q: A wet gas is produced through a two-stage separator system. Separator conditions are 580 psia and…

Q: ) Calculate the amount of lime and soda required for softening 9000 litres of water sample…

A: (i)The temporary hardness in water is due to the presence of calcium and magnesium carbonates and…

Q: What is the hydraulic fluid pour point requirement for a system which is operating -20° C A) -21° C…

Q: hydragen. Rld= 2.18x 10-l8J. speed af feght = 3.0 Xl0°mb. こ4 calculcate the womelyth f the hynt…

A: Interpretation- To determine the wavelength of light emitted in the given question where all the…

Q: Suppose you are designing a pipe to be used for a new process in diameter of the pipe you came up…

A: Solution -

Q: SeO2 Solvent/Heat H20 H3C. CH3 DDQ/C6H6 → ?. Reflux

A: Reaction 1 is selenium based oxidation of aldehyde which gives ketone at two position via 2,3…

Q: (a) Water in vadose zone contains chlorobenzene of concentration 40 mg/L. What is the equilibrium…

A: “Since there are multiple questions and it is not mentioned that which one has to be solved so I am…

Q: Your 155 Ib client needs to work at 55% of their VO2max. You determine their VO2max to be 33.78…

Q: Q) If 25m VToluene and Voit 25ml Viwater ooml * N NacH 0.IN mwt find wt :

A: Totla volume is given by sum of all volume= 100 + 25 + 25 = 150 mL Volume (L)= 150/1000 Volume (L)…

Q: Q26. Calculate the air standard efficiency and work of an Otto cycle, has a clearance volume of…

Q: Suppose you have an initial chlorine concentration of 5%. Then out of that, you are told to prepare…

Q: For numbers 39 to 40: In a carbon dioxide plant monoethanolamine is used to absorb CO2 from…

A: 39.b

Q: decide if the given statement is true or false,and give a brief justiﬁcation for your answer.If…

A: The given statement is - In a chemical mixing problem involving two tanks, the rate at which ﬂuid…

Q: Make a schematic diagram for the procedure below: A. Constant weighing of the crucibles Bring two…

A: A question based on analytical process that is to be accomplished.

Q: When trying to calculate the Kav for glutamate dehydrogenase I keep getting a negative value using…

A: Glutamate dehydrogenase is an enzyme which has a role in living beings to generate ammonia for urea…

Q: According to this, find the amount of CO2 absorbed by titration?

Q: liquid hydrogen (LH2) tank is a double-hulled tank composed of cold drawn and annealed 316 stainless…

A: Answer:- Factor leading to the failure of LH2 tanks such tanks may also be refered to as cryogenic…

Q: 2. In an ethanol production plant, a separator produces a 99% ethanol product from a feedstock…

A: Given:- The mass flow rate of feedstock stream mF = 450 lb/min Mass fraction of ethanol in feed…

Q: 25L bag was filled with air, a 10uL sample was then injected into the bag to make 50ppmv vapor…

Q: . A straight horizontal pipe with a diameter of 1.0 cm and a length of 50 m carries oil with a…

A: Given as Diameter of pipe=1.0cm length=50 m coefficient of viscosity=0.12 N.s/m2 Gauge pressure at…

Q: un plant, on Is as Tollows. CHs + H2 - CH12 The complete process of producing cyclohexane uses a…

Q: Which part of the GC equipment does separation takes place?

A: GC (Gas chromatography) is an analytical technique used to separate the chemical compounds of a…

Q: The feed to the reactor contains equimolar amounts of methane and oxygen. Assume a basis of 100 mol…

Q: (a), estimate the specific cake resistance and the resistance of the filter medium to filtrate flow.

A: Solution Filtration, the method within which solid particles in a very liquid or gassy fluid square…

Q: The following gas-phase reaction takes place in a closed, constant-volume batch reactor at…

A: We have given a reactor contains nCO = 0.564 kmol = 564 mole nO2 = 1 kmol = 1000 mole nCO2 = 1…

Q: A spent sulfuric acid solution is brought up to strength for a pickling process in a mixer. Spent…

A: Solution GIven that, concentration of spent solution is 3% This is mixed with 50% Sulphuric acid…

Q: Air with a dry-bulb temperature of 38oC and a wet-bulb temperature of 27oC is scrubbed with water to…

A: Air Inlet Conditions: Dry-bulb Temperature= 38oCW Wet-bulb Temperature= 27oC Now, From Psychrometric…

Q: 2. The solution gas-oil ratio of a crude oil is 800 scf/stb at 3,000 psia and 120 F. Given the…

A: GIVEN:- The solution gas-oil ratio of a crude oil is 800 scf/stb at 3,000 psia and 120 F. Given the…

Q: For pilot test purpose in mud lab. , 1L of FWB has been prepared , if the volumetric percentage of…

Q: Screen reader description: The Ordinary Phases of Carbon Dioxide. Pressure (Pa) 10 to the power of 0…

A: Given: Temperature range = 0 K to 700 K Pressure range = 100 Pa to 108 Pa Plotting following…

Q: c. An Analytical laboratory at SMU has a bottle of concentrated HCI solution labelled, specific…

A: C). given that Specific gravity = 1.2 g/cm3 the density of the solution will be equal to the…

Question

Q4-A vertical cylinder tank with diameter of 12m and depth of 4m is filled to the
top with water at 20C°. If the water is heated to 100C°, how much water is spilled
over, and what is the percentage in mass reduction. (at 20C° density=998Kg/m3,
at 100C° density%3D958KG/m3).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

2. A solution composed of 50% ethanol (E1OH), 10% methanol (MeOH), and the rest are (H2O) is fed in weight at the rate of 100 kg/hr into a separator that produces one output stream at the rate of 60 kg/hr with the composition of 80% E1OH and 15% MeOH, and the second output stream of unknown composition. Calculate the composition (in wt. %) of the three compounds in the unknown stream and its flowrate in kg/hr. (Remember to show the variable analysis)
A empty evaporating dish weighs 30.56g. You place 20.0mL of an NaCl solution in the dish plus the solution weighs 53.31g. You evaporatorate the solution to dryness ant find that the evaporatoring dish plus the residue weighs 32.25g. What is the w/v%? What is the w/w%? What is the molarity?
2-25. The compound is initially at 40°F. If the pressure is constant at P = 1 atm throughout the process, and the specific enthalpy of the compound is increased by 350 BTU/lb, what is the final temperature? m
Ex7; An aqueous solution of sodium hydroxide contains 20.0% NaOH by mass. It is desired to produce an 8.0% NaOH solution by diluting a stream of the 20% solution with a stream of pure water. Calculate the ratios (liters H20/kg feed solution) and (kg product solution/kg feed solution). F =? kg = 0.2 XNaOH P =? kg XH,0 = 0.8 F2 =? kg F2 = 0.08 kg Na0H/kg xH,0 = 0.92 kg H20/kg %3D 1
Two aqueous sulfuric acid solutions are available at a processing facility: 20.0 wt% H2SO4 (sg = 1.139) 60.0 wt% H2SO4 (sg = 1.498) It is desired to mix the two solutions such that the final product has a concentration of 4.00 M (sg-1.213). There is 100 kg of the 20% solution available. If all of this is to be used, calculate: The mass of 60% solution needed The mass and composition of the final product
A spent sulfuric acid solution is brought up to strength for a pickling process in a mixer. Spent solution at 3% sulfuric acid (by weight) is mixed with a 50% solution (by weight) to obtain the desired product concentration of 40% acid by weight. All are aqueous solutions. Determine all flowrates on the basis of 100 lbm/h of product. If the actual flow of the spent stream is 300 lbm/h, what must the flowrates of the streams be?
SKÜ-LMS A copper block of 127 g mass is produced by casting. Pressure of the solid block is decreased from 1 a (100000 Pa) to 0.01 atm (1000 Pa) by placing in a vacuum oven and temperature is raised from 0 °C to by heating in the oven at the same time. What is the volume change? B(Cu)=0.000016/K, K(Cu)=0.00000073/Pa, p(Cu)=8.92 g/cm3 at 273 K, MW(Cu)=63.5 g/mole Oa. 4.48 cm3 O b. 0.56 cm3 O c. No volume change occurs O d. Ne. 1.12 cm3 Seçimimi temizle
Q4/ a fuel mixture of 40% (C,H16) and 60% (C&H18) by volume is used in an engine having a 120 bore of 0 mm and stroke length of 145 mm , the compression ratio is 8.5. The percentage composition of dry products of combustion by volume is (CO, = 12%), (CO = 1.5%), %3D (02 = 2.5%) and the rest is N2. calculate the air/fuel ratio and the mass of residual gases left in the cylinder at the end of the exhaust stroke if the pressure and temperature are 1.1 bar and 720 k
QI/Prepare 0.1N of CH,COOH in 500 ml., Specific gravity 1.05 gm/cm and percentage 99.5% ?
3-9. A 40-cu ft tank is filled with air at 14.7 psia and 80°F. The tank also contains a 15-lb block of dry ice (solid CO2, specific gravity of 1.53 based on water). After the dry ice sublimes, the temperature is 30°F. What is the pressure? Assume ideal gas behavior.
6. Assume you have 1kg of an alloy consisting of 85 wt% Sn and 15 wt% Pb at a temperature of 184 °C. How much Sn (in kg) needs to be added to solidify the entire mixture without lowering the temperature? Composition (at% Sn) 20 40 60 80 100 327°C Temperature (°C) 300 200 100 (Pb) a + L 18.3 20 183°C a + B Liquid 61.9 40 60 Composition (wt% Sn) B+L 80 232°C 97.8 B al 600 500 400 300 200 100 100 (Sn) Temperature (°F)
4:19 < 1/153 During a cement production process, the rotary kiln temperature has reached a maximum of 1250 degrees Celsius. - What are your thoughts on: a) the chemical Share 4G .... .... composition, b) physical properties c) mechanical properties of the resulting product? Please interpret the product. < Edit 13 71% Delete = : More