True or False Q4: For each sentence below, put the word "True" for right sentence and "False"for wrong sentence.1. For indirect evaporative cooling, the two fluids are separated by a thinperforated wall of high thermal conductivity to enhance the heat transferbetween the two fluids. (2. The enthalpy of fusion for cold storage products is found from tabulatedproperties for each product. (3. Steam jet refrigeration utilizes water and refrigerants as workingrefrigerants. (4. In plastic piping system, the surge pressure due to water hammer can be50% of the pressure rating of the system. (5. The freezing temperature depends on the cooling capacity of therefrigeration system. (6. In cold storages, ventilation load can amount to be approximately as half therefrigeration load.7. In piping systems, bends are mostly subjected to erosion. (8. The use of chilled water in direct evaporative cooler increases the adiabaticefficiency. (9. Plastic tubes are widely used in refrigeration systems. (10. In direct evaporative cooler, the air undergoes a constant enthalpy process.).

1. For indirect evaporative cooling, the two fluids are separated by a thin perforated wall of high…

Q4: For each sentence below, put the word "True' for wrong sentence. 1. For indirect evaporative cooling, the two flui perforated wall of high thermal conductivity t between the two fluids. ( 2. The enthalpy of fusion for cold storage produ properties for each product. (

Q4: For each sentence below, put the word "True' for wrong sentence. 1. For indirect evaporative cooling, the two flui perforated wall of high thermal conductivity t between the two fluids. ( 2. The enthalpy of fusion for cold storage produ properties for each product. (

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 12RQ: The function of the pressure tank in an open-loop, geo-thermal heat pump well system is to prevent...

See similar textbooks

Similar questions

Q3: Explain in detail the differences between vapor compression systems and evaporative cooling systems. This comparison should present advantages, disadvantages, potential applications, and suitability of each system to the climate conditions of Iraq.
f. A well-built, wood-framed, single-family detached residence in Manila, Philippines, has a 15 ft by 20 ft family room with 10 ft high ceilings. The target inside design temperature is 72°F. If the air exchange rate of 0.4, calculate the sensible cooling load attributed to infiltration.
O Falge QUESTION 2 The refrigerant undergoes a change of phase during the heat-transfer process, the pressure of the retrigerant is the saturation pressure during the low supply and low rejection processes. True False QUESTION 3 Frequently, the vapor of the liquid leaving the condenser is lower than the saturation temperature. O True False QUESTION & The pressure of the iquid leaveng the condenser we be less than the pressure of the vapor entarng, wd etempernd the retigerant in the condenser. O Te QUESTION S Are many situations in which it is desirable to combine three cycles in series, either power systems or refigertion sytems, to take advantage of a very wide temperature range or to utilize what would otherwise be waste heat to improve etficiency O true O False QUESTION 6 A cycle can't be made very efficient, since the temperature differences between the two fluid streams can be controlled through careful design of the combined system. True
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
IDENTIFY THE FF: AIRCONDITIONING AND VENTILATION 1. Acts as a master controller which keeps the system inautomatic operation2. Adds heat to a fluid3. Ratio of the actual partial pressure of the watervapor in a space to the saturation pressure of purewater at the same temperature.4. Also known as the heat content of air-vapormixture5. Temperature as read on an ordinary temperature6. Temperature where in water will start to condense7. Equipment that removes heat8. Is the process of treating air9. Their purpose is to create atmospheric conditionsfavorable to human health, comfort and efficiency.10. The system is to maintain indoor conditions forwinter season
4. GoBrownsite is an obscure element with a molar mass of 126.2 grams per mol. Below is the cooling curve for GoBrownsite. How much energy needs to be removed from a 250.0 g sample of GoBrownsite knowing the following. Heat of Condensation AH = -165 kJ/°C • Specific heat of liquid GoBrownsite = 197 kJ/g-°C Heat of Freezing AH = - 231 kJ/°C Cooling Curve 80 e) to (1) 60 40 20 -20 Temperature 40 -60 -80 -100 (1) to (s) -120 Time
B// What are the methods of draught in cooling towers. Demonstrate them with drawings. What is the relationship between the cooling tower and condenser. Q4IIA// Prove for the condenser: %3D + Cow (Tw2-Tw1) when the temperature of cooling water outlet and inlet is equal to saturation temperature of steam and the condensate leaving the condenser respectively; also, the inlet of condenser is dry steam with unity latent heat. Twi 1
Heat-Transfer Coefficient in Single-Effect Evaporator. A feed of 4535 kg/h of a 2.0 wt % salt solution at 311 K enters continuously a single-effect evaporator and is being concentrated to 3.0%. The evaporation is at atmospheric pressure and the area of the evaporator is 69.7 m². Saturated steam at 383.2 K is supplied for heating. Since the solution is dilute, it can be assumed to have the same boiling point as water. The heat capacity of the feed can be taken as cp = 4.10 kJ/kg · K. Calculate the amounts of vapor and liquid product and the overall heat-transfer coefficient U. 8.4-1.
1.) Determine the refrigerant name and chemical formula of R-22 2.) An ice plant produces 20 tons of ice per day at -15oC from water at 25 oC. If miscellaneous losses are 12 % of the freezing and chilling load, calculate the refrigeration capacity of the plant, in TR.
What are chilled liquid treatment process and condenser water treatment process in refrigeration and air conditioning?
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
explain the principle of operation of a cooling tower and neatly sketch section, analyse a crossflow cooling tower.