Q4. A linear time-invariant system is described by a linear constant-coefficient difference equation with initial rest conditions. The output when is input is the unit step is called step response and is given by the formula: yln] = [$)" – (-)"1 u[n – 2] (a) Find a formula for the impulse response of the system. (b) Determine the difference equation of the system. (c) Determine an input so that the output would be the unit-step signal.

Q4. A linear time-invariant system is described by a linear constant-coefficient difference equation with initial rest conditions. The output when is input is the unit step is called step response and is given by the formula: yln] = [$)" – (-)"1 u[n – 2] (a) Find a formula for the impulse response of the system. (b) Determine the difference equation of the system. (c) Determine an input so that the output would be the unit-step signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Define Impulse Voltage? What are the different types of Impulse voltages? What are standard Impulse voltages, mention their values?
LESSON : Control Systems SUBJECT : Analysis and Design of Control Systems In the mechanical system given in the figure; a. Obtain the transfer function with input-F(t) and output-x2(t) (all initial values of the system are zero). b. Draw the electrical equivalent of the system (F(t): voltage source). 1 k3 ki Ebs 162 ! Please ! Solve it using a block diagram and a signal flow diagram (SFD). Solving using Laplace transforms
(d) what is the peak value of the step response??( Need only handwritten solution please otherwise downvote)
In the electrical network given in the Figure, the output voltage is taken over the coil. R = 1k ohm, C = 1μF and L = 1 mH. a)Since the switch is closed at time t = 0, the input and the relationship between output voltages. Determine the differential equation shows. b)Find the transfer function. c)Unit impulse and unit step function type input voltages versus output voltages calculate and change changes according to time. Draw it to scale.
b) The unit step response of a first order system is shown below: Develop the transfer function of this system. Please include detailed steps. Hint: Please find the time constant and the constant gain (the numerator).
the linear convolution output y(n) is 93 and length impulse response h(n) is 18. then the length of the input sequence x(n) assuming that the impulse response length is double is ................................... . the question is for digital signal processing cource.
From transfer function used in simulation, calculate all step response characteristic parameters and compare your result with value obtained from Assignment
a) Design a circuit using 741 op amp IC and 555 timer IC, to generate both Pulse Width and Pulse Position modulated signals. Perform the required calculations to obtain the width of the PPM signal as 200μs. Draw the clear circuit diagram and calculate the values of resistors and capacitors used. b) Simulate the circuit designed in part (a) using appropriate simulation tools(Multisim or Tinkercad) and obtain the output. The answer should include details such as aim, brief procedure, screenshot of simulation circuit along with resultant waveforms and calculations of the practical time-period obtained for PPM output. c) Plot graphs with clear labels and scales for message, carrier and output signal (PWM and PPM). Also discuss your inference and reflection on the results obtained. [Note: Plot graphs on a normal graph paper by hand and attach the scanned copy to the assignment]
a) Reduce the following block diagram (Figure Q2) to a single transfer function C(s) T(s) : R(s) C(s) R(s) 1 NC NC NC 5 3 2 NC 3 Figure Q2 b) Convert the block diagram of FigureQ2 to a signal flow graph and find transfer function using Mason's rule
define impulse voltage ? what are the different types of impulse voltages ?
The filtering stage of a biomedical device passes signals with frequencies ranging between 20 Hz and 500 Hz while the stage delivers a total gain of 48 Design the electronic circuit of the filtering stage using appropriate numbers of operational amplifiers,resistors, and capacitors. (The filtering are all 1st order active filters and the maximum possible gain is limited to 10 for a single amplifier) B. In the circuit, the capacitors are all 318 nF and the feedback-resistors are all 10 k.ohm find the values of the remaining resistors in the circuit
Discuss the effect of increasing and decreasing proportional gain to the system output. Discuss the effect of increasing and decreasing derivative gain to the system output. Discuss the effect of increasing and decreasing the integral gain to the system output. 4. Discuss some advantages of using Simulink over the MATLAB codes I WANT THE ANSWER FOR THIS QUESTION WITHOUT PLAGIARISM