Q6. A pump moves water horizontally at a rate of 0.02m /s. Upstream of the pump where the pipe diameter is 90mm, the pressure is 100kPa. Downstream of the pump where the pipe diameter is 30mm, the pressure is 350KPA. If the loss in energy across the pump due to fluid friction effects is 170N.m/kg, determine the hydraulic efficiency of the pump. (Pwater = 999 kg/m³)

Q6. A pump moves water horizontally at a rate of 0.02m /s. Upstream of the pump where the pipe diameter is 90mm, the pressure is 100kPa. Downstream of the pump where the pipe diameter is 30mm, the pressure is 350KPA. If the loss in energy across the pump due to fluid friction effects is 170N.m/kg, determine the hydraulic efficiency of the pump. (Pwater = 999 kg/m³)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A groundwater well with produces 80 m/hr. and has a hydraulic conductivity of 20 m/d. Calculate the following: a. The length of the screen b. The diameter of the delivery pipe. c. The velocity head and the friction losses in the delivery pipe. d. What is the required power of the pump if the abstraction efficiency was 70%? Assume the following: The percentage of the opening in the screen is 17%, the entrance velocity is 1.55 cm/sec, the diameter of the screen is 30 cm, water velocity in the tube is 2.2 m/sec. Assume any missing data.
A centrifugal pump delivers 227 m³/hr of water from a source 4 meters below the pump centre line to a pressure tank whose pressure is 2.8 kg/cm² . Friction loss estimates are 2 meters in the suction line and 1 metre in the discharge line. The diameter of the suction pipe is 250 mm and the discharge pipe is 200 mm. Find: a. The water horsepower b. The kW rating of the driving motor if the pump efficiency is 70%
It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 6. 3. 7. 5.
Determine the least number of stages for a multi-stage pump to deliver 80 L/s against a total head of 240m when running at 1450 rpm if the specific speed (per stage) must not be less than 670. Select the correct response: 6. 3. 4. 7. 8
B- Calculate the power required for a water pump used in a closed system with flow rate Q=0.0076 m³/s. Assume that section area=0.00511 m² and at the area at the discharge is 0.0037 m². As AJ Water Suction Discharge pump Inlet gauge pressure=147 kPa Outlet gauge pressure=250 kPa
A centrifugal pump delivers water at a rate of 0.03 m /sec to a height of 18 meters through a pipe of 100 mm dlameter and 90 m long. If the overall efficiency of the pump is 75 %, find the power required to drive t e pump. (Take f 0.012).
Len is asked to design a small water pump for an aquarium. The pump should deliver 18.0 Lpm of water at a net head of 1.6 m at its best efficiency point. A motor that spins at 1200 rpm is available Suppose the pump is modified by attaching a different motor, for which the rpm is 1800 rpm. If the pumps operate at homologous points (namely, at the BEP) for both cases, predict the volume flow rate and net head of the modified pump. Calculate the pump specific speed of the modified pump, and compare to that of the original pump. Discuss.
Q1/ liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to 45° elbow 8 m Fig. (1) Globe valve Tank 5 m supply water to the tank at the rate of 245 I/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the pump required 12 m NPSH is it suitable to prevent cavitation for this system? why? Given that: u = 0.0016 Pa.s; p 850 kg/m', e/d 0.0035, (Le/d) of Globe valve (open) = 240 (Le/d) of 45° ēlbow = 24 and Pv = 36.6 kPa 25 m 45° Reservoir 45° elbow
What is the horsepower requirement for a water pump, if the required flow rate is 200 gpm and the required pressure increase assigned to the pump is 32 psi?
Correct this problem with step-bystep please: A pump moves water horizontally at a rate of 0.02 m^3 /s. Upstream of the pump, where the pipe diameter is 90 mm, the pressure is 120 kPa. Downstream of the pump, where the pipe diameter is 30 mm, the pressure is 400 kPa. If the loss in energy across the pump due to fluid friction effects is 170 N.m/kg. Determine the hydraulic efficiency of the pump.
4. The discharge pipe of a pump is 400 mm in diameter delivers 0.5 m3/sec of water to a building which maintains a pressure of 100 Kpa at a height of 30 m, what power must be furnished by the pump?
A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down back into the tank. The diameter of the impeller of the pump is 145 mm, the pump speed is 2900 rpm. The equation to calculate the flow V in the valve depending on the pressure drop differential pressure (dp) in the valve isV = 4 * sqrt (dp), whereas V is in m³/h and dp in bar. Please estimate the water flow.