Question 1 The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is 0 = 20°. mm B 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the internal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston? 3.

Question 1 The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is 0 = 20°. mm B 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the internal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston? 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is e = 20°. 250 mm B e 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the internal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston?
A hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coil
Fatigue angle Failure (record number of cycles before failure) Large Metal Paperclip in Small Metal Small Plastic Large Plastic Paperclip degrees Paperclip Paperclip 45° 90° 180° 270° Evaluate: 1. Which type of paperclip lasted the largest number of cycles before failure (small metal, large metal, small plastic, or large plastic)? 2. Which paperclip lasted the least number of cycles before failure? 3. Which angle (45°, 90°, 180°, and 270°) was associated with the fewest cycles before failure? 4. Give three reasons why different paperclips may break at different number of bends?
Question 1 The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is 0 = 20°. 250 mm/ B 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the intermal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston?
Question 1 The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is 0 = 20°. 250 mm B 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the internal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston?
A nut which is connected to a lead screw is moved in a horizontal plane against a force of 100kN at a speed of 4mm/sec by electric motor powered screw. The following data is given Single start square thread screw Pitch of the screw=6mm Outlet diameter of the screw =40mm Co-efficient of friction of the screw thread =0.15 Efficiency of the motor=85% Determine the power required and efficiency of the screw The following data is refers to a screw jack. The vertical load on the screw=20kN Force applied at the lever end whose length=80cm The mean radius of the screw-2.5cm Pitch of the screw=1cm Co-efficient of friction between the screw thread and the nut=0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
3. One way of quantifying the energy needed to create fracture in a material is with a Charpy test, shown to the right. A large pendulum (here m= 50 kg, ka = 1.75 m) is released from rest 1.25 m when 0= 0°. The pendulum hits a notched sample of standard size of the material to be tested at S. The pendulum swings up the other side, with its angular distance measured by a ratcheted scale. The system is designed to minimize frictional losses, so the difference in the energy at release and the maximum energy in the follow through is the energy absorbed in fracturing the sample. For the Charpy apparatus shown, what is the angular velocity and kinetic energy of the pendulum the instant before it hits the sample at S when 0=90°.
Question 5 Answer the following questions concisely (no more than half a page per question): a What do you understand by strength, stiffness and stability in the Mechanics of Solids context? b Identify, sketch and explain how to calculate all possible failure modes of a bicycle chain (for the link plates and the pin). c What is/are the difference(s) between von Mises (Maximum Distortion Energy) and Tresca (Maximum Shear Stress) failure criteria? d Give a structural engineering explanation to the placement of pinnacle statues on top of flying buttress columns of Gothic Cathedrals. e Give a structural engineering explanation to the structural failure of the "grabbing" arms of the capture vehicle used to raise the Russian submarine K- 129.
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
250 mm long. The piston has a mass of 1 kg and the speed is 1800 rpm. The... tinatiynamimmal A Am A petrol engine 100 mm in diameter and 120 mm stroke has a connecting rod 250 mm long. The piston has a mass of 1 kg and the speed is 1800 rpm. The gas pressure is 0.5 MPa at 30° from top dead centre during the explosion stroke. What is the force on piston due to gas pressure?
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
In-1' 16+29 CHAPTER ENGINEERS MECHANICS STATICS り」 arc ( 24 X(x Sample Problem 6.4.2 JQ) aX9 142 i JA V4 TuS 31 An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. 800 N.m dre 2.R 1. Which Tension is larger, TA or TB? Explain 2. What is the angle of contact in radians? 60 3. What is the value of the ratio TA/TB? A B X*ッー Sin=d 6+ミ 2(I+(T Tarc (2) 4)e Eら、1.2 J =3.