Question 2. The manometer in the figure is used to measure the pressure difference between two points in the pipe. The density of the water in the pipe is 1000 kg/m3 and the valve is open. If the readings on the manometer are z1= 100 mm, z2= 250 mm and h= 90 mm, how many N/m2 is the difference between P1 and P2? watelif Valve Dx aik

Question 2. The manometer in the figure is used to measure the pressure difference between two points in the pipe. The density of the water in the pipe is 1000 kg/m3 and the valve is open. If the readings on the manometer are z1= 100 mm, z2= 250 mm and h= 90 mm, how many N/m2 is the difference between P1 and P2? watelif Valve Dx aik

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7) For the manometer setup shown, determine the difference in pressure between A and B. oll, s = 0.85 Water 680 mm Bo 1700 mm YWater 8) A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is h. 100 mm re A Mercury A B Oil, s = 0.90 %3!
Subjact: Data: An inverted u tube manometer is connected to two horizontal pipes A. and 8 threugh which water is flowing The vertical distance between axes of the se pipes is 30 cM When an oil SG=0.8 îs uced as a Jauge fluid, the vertical heigh 1s of water columos in the two limbs are found to be the same and equal to 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. C. 30 cm 35 cm 35cm tw ater 30cm water
• A simple U tube manometer is given below. The pressure at which side is higher? o Left o Right o Left = right • In order to calculate the pressure difference at locations 1 and 2 (P2 - P1), we need to know the length of the inclined tube L, as is shown below. o True o False A fow section fow device Fluid
flow of water in the below diagram is from point X to Y. The oil is in the e inverted U-tube manometer. The mercury is in the bottom of the manome ressure difference P -P in kPa?
Weter flows up a tapered pipe (figure). A differential mercury manometer is attached to the pipe at Wand B. The pipe has a diameter of 200 mm at A and 100 mm at B, the point B being 1 m above the alot A. Obtain the deflection in the manometer corresponding to a discharge of 50 L/s. Neglect the friction in the pipe. Relative density of mercury 13.6. %D 100 mm 1 m 200 mm
1. A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. ₪t Mercury o..A 2. A manometer is attached ched and the mercury. to a water tank shown in the figure (a.) find the height of the free water surface above the bottom of the tank; (b.) Find the pressure at the interface of the water to a O water ROPERTON 100mm 0.15m 0.15m Oi, s 0.9 0.2m Hg(13.6)
1. Water is flowing in a wide open channel as shown in the figure. Two pitot tubes are connected to a different manometer containing oil (sp.gr. = 0.82). Find the velocity at m point A and point B in - oil (op.gr.=0.82) 2 m wafer sarfece
Water flows through a pipe reducer shown in figure 2. The static pressure in the large diameter pipe and the small diameter pipe are measured by the inverted U-tube manometer containing oil of specific gravity less than one. Determine the manometer reading, thus show that h is given by the equation h = ng(1-SG) la SG Water Figure 2 The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B.
Subjact: Data: An invertedu tube manometer is connected to two horizontal pipes A. and 8 threugh which water is flowing The vertical distance between axes of these pipes is 30 cM When an oil SG=0.8 îs uced as a Jauge fluid, the vertical heigh 15 of and equal t0 water columos in the two limbs are found to be the same 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. C. 30 cm 35 cm 35cm tWater 30cm water
1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly ... a) 1.35 b) 1.5 c) 1.75 d) 2.00
ns HR NATER om 2. OIL MEROURY A manometer connects an oil pipeline and water pipeline as shown. Determine the difference in pressure (P1-P6)between two pipes using the readings on manometer. Use S.G oil- 0.96 and S.G Hg= 13.6 Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa Decimal Places required in the final answer:3
A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is n. 100 hm re A Mercury B Oil, s = 0.90