QUESTION 3 A flat plate, manufactured from Perspex, is drawn submerged through 25°C still water at a velocity of 1.3 m/s. The plate is 0.35 m wide and 1.5 m long. Determine: 3.1 the laminar to turbulent transition position along the length of the plate. 3.2 the boundary layer thickness at this position.

QUESTION 3 A flat plate, manufactured from Perspex, is drawn submerged through 25°C still water at a velocity of 1.3 m/s. The plate is 0.35 m wide and 1.5 m long. Determine: 3.1 the laminar to turbulent transition position along the length of the plate. 3.2 the boundary layer thickness at this position.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.50P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
A flat plate, manufactured from Perspex, is drawn submerged through 25°C still water at a velocity of 1.3 m/s. The plate is 0.35 m wide and 1.5 m long. Determine: 3.1 the laminar to turbulent transition position along the length of the plate. 3.2 the boundary layer thickness at this position.
Engine oil at 40°C flows over a 20-m-long & 3-m-wide smooth flat plate with a free-streamvelocity of 50 m/s. Determine the drag force acting on upper side of the plate when:a) Flow is parallel to plate length.b) Flow is parallel to plate width.
Engine oil at 40°C flows over a 20-m-long & 3-m-wide smooth flat plate with a free-stream velocity of 50 m/s. Determine the drag force acting on upper side of the plate when:a) Flow is parallel to plate length.b) Flow is parallel to plate width.
Engine oil at 40°C flows over a 20-m-long & 3-m-wide smooth flat plate with a free-streamvelocity of 50 m/s. Determine the drag force acting on upper side of the plate when:a) Flow is parallel to plate length.b) Flow is parallel to plate width. kindly give me the correct solution.
Consider a laminar flow over a flat plate of length L = 1m. The boundary layer thickness at the end of the plate is dw for water, and 6, for air for the same free stream velocity. If the kinematic viscositics of water and air arc 1x106 m/s and 1.6x10-5 m/s. respectively, the numerical value of the ratio, w
Water at 10°C flows over a 1.1-m-long flat plate with a velocity of 0.55 m/s. If the width of the plate is 2.5 m, calculate the drag force acting on the top side of the plate. (Water properties at 10°C are: ? = 999.7 kg/m3, ? = 1.307 × 10−3 kg/m·s.) (a) 0.46 N (b) 0.81 N (c) 2.75 N (d ) 4.16 N (e) 6.32 N
Q4 : Air is flowing over a long flat plat velocity 8 m/s . Determine the distance from the leading edge of the plate where the flow become turbulente , and the thickness of the boundary layer at that location . Take the properties for air: k = 0,02735 W/m.°C , v= 1.798 × 10°m²/s , Pr = 0.7228
A 1.5-m-long and 0.5 m wide flat plate is immersed in water flow with velocity of kg 5 m/s. (F = 1000 =1.02 x10- m Determine; (a) The boundary layer thickness at leading edge of the plate, (b) The drag coefficient and the drag force, (c) the drag coefficient and force, if the flow is laminar at the entrance (Rex, ait= 106), (d) the drag force, if the roughness height & is 0.2 mm on the plate.
Consider a flat plate as shown below. Freestream air approaches parallel to the plate with the conditions shown. Assume air= 1.63 x 10-5 kg/m-s. Determine; a) the overall drag per unit depth (N/m) for the laminar flow case, b) the overall drag per unit depth (N/m) for the turbulent flow case, and M₁ = 0.4 alt. = 5,000 m L = 0.75 m
A 0.8-m-outer-diameter spherical tank is completely submerged in a flowing water stream at a velocity of 2.5 m/s. Calculate the drag force acting on the tank. (Water properties are: ? = 998.0 kg/m3, ? = 1.002 × 10−3 kg/m·s.) (a) 878 N (b) 627 N (c) 545 N (d ) 356 N (e) 220 N
Aft of the transition point between laminar and turbulent flow A. the boundary layer gets thinner and the speed increases B. the boundary layer thickens and the speed decreases C. the mean speed increases and the surface friction increases D. the mean speed increases and the surface friction decreases