QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a diameter of 10". What is the velocity at each section? Section 1= 5.89 ft/sec Section 2= 9.2 ft/sec Section 1- 8.9 ft/sec Section 2= 6.0 ft/sec Section 1= 9.9 ft/sec Section 2- 9.9 ft/sec Section 1- 4.89 ft/sec Section 2= 6.58 ft/sec

QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a diameter of 10". What is the velocity at each section? Section 1= 5.89 ft/sec Section 2= 9.2 ft/sec Section 1- 8.9 ft/sec Section 2= 6.0 ft/sec Section 1= 9.9 ft/sec Section 2- 9.9 ft/sec Section 1- 4.89 ft/sec Section 2= 6.58 ft/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section? A. Section 1: 5.89 ft/sec Section 2: 9.2 ft/sec B. Section 1: 8.9 ft/sec Section 2: 6.0 ft/sec C. Section 1: 9.9 ft/sec Section 2: 9.9 ft/sec D. Section 1: 4.89 ft/sec Section 2: 6.58 ft/sec
For the system of pipes shown in the figure below, the direction of flow is from 1 to 2. Which of the following is INCORRECT? Neglect minor losses. 1 Pipe A O a. hL1to2 = hƒA + hfB O b. hfc = hfD O c. O d. QB = QA Q₁ = QB + Qc + QD Pipe C Pump Pipe D P Pipe B 2
1. The total headlost from A to E as shown is 20 m. Use n = 0.011 to all pipes Compute for the discharge at line 2 Compute for the discharge at line 1 Compute for the discharge at line 4 (BCD) Pipe Diameter Length in (mm) 600 AB BC CD BD DE 450 450 500 600 Q1 = Q3 Q1 = Q2 + Q4 hfr = hf₁ + hf₂ + hf3 hf₂ = hf Q4 = 0.2974 m³/s Q₁ = 0.7663 m³/s Q3 = 0.7663 m³/s Q2 = 0.4689 m³/s m 600 400 450 600 650 1 B 2 C D 3 E
What is the head loss between points A and D when the flow rate is 6² the flow rate for each of the branches (1 and 2) in the parallel pipes and the head o segment BC. Neglect Minor Losses B C D Pipe Segment Length (m) Diameter (m) Friction Coefficient (n) AB 100 0.75 0.014 150 0.5 0.008 90 1 0.035 75 1.25 0.021 CD 1 2
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a %3D special fluid of SG=1.2, What is the direction of the flow? 1 550mmo 7.88m 2 2.95m Datum O point 1 to 2 O No flow point 2 to 1
1. Please show your understanding of 4R in equation (4.6) by assuming it is a full pipe flow with a pipe diameter d. To fpV /8 f v? (4.6) %3D %3D %3D L. yR YR 4R 2g
A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Determine the following: a.) Discharge flowing in the pipe, f = 0.012; b.) Discharge flowing in the pipe, n = 0.014; c.) Discharge flowing using C = 120 im iong PIune tnat Tuns on
enough pro Fuck T Question 3 Water flows at a velocity of 1.5 m/s in a 200 mm new ductile iron (CH = 130) pipe. Estimate the headloss over a kilometer length of pipe using: (a) The Hazen-Williams equation (b) The Manning formula (n=0.012) (c) The Darcy-Weisbach equation (assume temperature of 20°C) 3gd
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Problem 6: EGL and HGL (II) Part A Why is the energy gradient (i.e., the slope of the EGL=EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part B Why are the EGL and HGL not parallel in this figure? (<10 words) H V² 28 HGL 2 EL Hydraulic grade line, slope = S, Ax - Energy line, slope = Sy Bed ylope Datum h₂ - Az 2 4 X
14. the flow rate in pipe with diamiter 115mm and the flow is turbulent .the kinematic velocity=D1.15* 10^-6 will be 2.076*10^-4 O 4.156*10^-4 15. The type of flow if the flowrate is 0.1 I/s.the diamiter is 100 mm.the kinematic viscocity=D1.003*10^-6 is TURBULENT O LAMINAR 16.if the flow rate is 1.5 and the flow is laminar.viscocity is 1.003*10^-6. The diamiter will be 476mm true false K
Determine the discharge at pipeline 2 in lit/sec assuming f=0.02 for all pipes. 700 m 450mm diam. 0.86m3/s Pipe 2 800 m 400mm diam. Pipe 3 700 m 500mm diam. O 200 100 250