Question A 3 phase, 10 kW, 400 V, 4 pole, 50 Hz, star connected induction motor draws 20 A on full load. Its no load and blocked rotor test data are given below: No Load test: 400V 6 A 1002 W Blocked Rotor test: 90 V 15 A/62 W Neglecting copper loss in no load test and core loss in Blocked Rotor test, estimate motor's full load efficiency.

Question A 3 phase, 10 kW, 400 V, 4 pole, 50 Hz, star connected induction motor draws 20 A on full load. Its no load and blocked rotor test data are given below: No Load test: 400V 6 A 1002 W Blocked Rotor test: 90 V 15 A/62 W Neglecting copper loss in no load test and core loss in Blocked Rotor test, estimate motor's full load efficiency.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…
tørque in new Draw the power flow diagram of induction motor and explain the different power losses, the air gap power and the converted pòwer. Explain how by solving the equivalent circuit of three phase induction motor the input current, input power factor, air gap power, rotor copper loss, converted power, output power and induced torque are calculated. (b)A 440 V, 50 Hz, 2-pole, Y-connected induction motor is rated 75 KW. The equivalent circuit parameters are: R, = 0.0752 R, = 0.0652 X = 1.22 Pare = 1.1kW X, = 0.172 X, = 0.17Q Pe =150W PEAW = 1.0kW For a slip of 0.04 find the line-eurrent, the stator"power factor, the stator copper_loss, the air gap power, the converted power the induced torque and the Toad torque. MISC
a) Why the slip of induction motor is never zero, b) What happens if the slip of induction motor is one, c)What is the value of the slip for an induction motor at no load and full load.
A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
Q2 ) A 220-V, 1.5-hp 50-Hz,wo-pole, capacitor-start induction motor has the following main-winding impedances: R1=1.40 2 X1=2.01 S Xm= 105 2 R2 = 1.50 2 X2=2.01 S2 At a slip of 0.05, the motor's rotational losses are 291 W. The rotational losses may be assumed constant. . Find the following quantities for this motor at 0.05 slip: (b) Stator Power factor (e)Pout (f) Tele (a) Stator current (d) PAG (c) Input Power (g) TL (h) Pconv (i) Efficiency
Explain torque speed/torque slip characteristics of 3 phase induction motor.
How rotor winding is derived the power in the three-phase induction motor? O a. from Single phase supply O b. from stator winding O c. None of the above O d. from slots
1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
A 3 phase, 400-V, 50 Hz 4 pole induction motor is fed from a 3-phase supply and runs of 1425 rpm. The frequency of the rotor emf is.....