RAX RAY 0 F₁ KN F₂ kN D The figure above is a pin-joint frame with angle = 30° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAx= 10kN and RAY=25kN, calculate the forces in members AB and AF, denoted by FAB and FAP respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB Enter FAP: ROY

RAX RAY 0 F₁ KN F₂ kN D The figure above is a pin-joint frame with angle = 30° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAx= 10kN and RAY=25kN, calculate the forces in members AB and AF, denoted by FAB and FAP respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB Enter FAP: ROY

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

RAY B F F₁ ROY
Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure, mark the salient points in the diagram. Neglect the self-weight of the beam, where F1 =10 N, F2 =60N, F3 =30 N, F4 =1ON, a =5 m, b=2 m, c=3 m, d=5 m F4 F3 F2 F1 E A d. a
A transmission tower (a truss) for supporting electric wires is shown. The load of wire at D is shown as force F1 at an angle of a and the load of wire at A is shown as force F2 at an angle of B. Using the values given in the table below: F1 (N) F: (N) a (deg) B (deg) w (m) h (m) Value 150 70 30 60 2 a) Find the reaction forces at supports Y and Z. b) Determine the forces supported by members DO, DM, SV, and UX and specify whether the member is in Tension or Compression. M Q B F1 F2 T W X h
GIVEN: DISTANCES CO= 7m BO= 7m OD= 8m AD= 8m GIVEN: WEIGHT W1= 195 N W2= 295 N GIVEN: ANGLE X= 55 Degree Y= 48 Degree SOLVE: (a) Tension at CB in NEWTON (b) Reaction at point O in NEWTON PLS PLS SOLVE AND SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. ALSO, DRAW THE FREE-BODY DIAGRAM. ROUND OFF IN 4 DECIMAL PLACES.
ENTER YOUR ANSWER THE WAY I SPECIFY HERE IN ADDITION TO DOING IT ON SCRATCH PAPER 400 N 800 N B D A E C 2 m Use the method of sections to calculate the axial force in members AC and BC. Enter your answer in the following way rounded to the nearest whole number. Example If your answer is TAC 2 N tension TBC =3.1 N compression. enter 2Tension;3Compression Enter TAC then TBC (no space)
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 42563-Nload, using the following data: length of steel = 1.56 m, length of bronze = 2.18 m Area of steel = 563 mm, Area of bronze = 233 mm Modulus of elasticity of steel = 193 Gpa, Modulus of elasticity of bronze = 82 Gpa x = 0.69 m, y = 1.03 m, and z = 0.79 m.
Using the information given in the figure, the reaction at points P and Q Calculate the forces as [kN].
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 42758-Nload, using the following data: length of steel = 1.27 m, length of bronze = 2.06 m Area of steel = 522 mm, Area of bronze = 239 mm Modulus of elasticity of steel = 216 Gpa, Modulus of elasticity of bronze = 84 Gpa x= 0.69 m, y = 1.08 m, and z = 0.86 m. Round off the final answer to three decimal places. ... Bronze Steel Ey te z
OP •C h W The man in the diagram is trying to move a large box by pushing on it with a force, P. The box weighs 300 N and its centre of gravity is located in the centre of the box (point C). Given: a = 1.8 m b = 0.8 m h= 0.9 m What is the minimum force that will cause the box to tip? Please include the unit ("N") within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 Newtons please input: 55.6 N). Answer: What is the minimum coefficient of static friction that will permit tipping to occur? Please do not include the unit s (as there are none) within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 please input: 55.6). Answer:
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 45846-Nload, using the following data: length of steel = 11 m, length of bronze = 2.3 m Area of steel = 562 mm, Area of bronze = 335 mm Modulus of elasticity of steel = 195 Gpa, Modulus of elasticity of bronze = 80 Gpa x= 0.55 m, y = 1.12 m, and z = 0.78 m. Round off the final answer to two decimal places. ... Bronze Steel
RAY F Enter Fpc: Enter Fr The figure above is a pin-joint frame with horizontal member length 1 = 2m and vertical member length h = 4m. (Note that the diagram is not to scale.) You are given that F₁ =45kN, RAY = 15kN and Rpy = 30kN. Use the method of sections to calculate the forces in members BC, FC and FE. Enter your answers in kilonewtons (kN) correct to 2 decimal places. Enter Fac: KN KN F₁ KN RDY
Consider a rigid rod that is subjected to two external forces and is fixed to the wall at A. The following figure displays the rod's free body diagram. Answer the following questions using the provided FBD. 2.5 -1 1 3.5 The support reaction at A along x-axis (A) is The support reaction at A along y-axis (Ay) is The support reaction at A along z-axis (A.) is The Moment reaction at support A about x-axis (Ma) is -1 n 1 0 -2.5 2.5 -1 -3.5 5.5 -5.5 -0.5 0.5 A₂ Mx4 Z M₂ My KN KN KN 3m KN.m 1m 1 KN 2m 2.5 KN