Refer to the figure. Let the mass of the block be 8.10 kg and the angle 9 be 25.0°. Find (a) the tension in the cord and (b) the normal force acting on the block. (c) If the cord is cut, find the magnitude of the block's acceleration. (a) Number 33.54 (b) Number 71.94 (c) Number -4.14 Units Units N m N Frictionless Units m/s^2 <

Refer to the figure. Let the mass of the block be 8.10 kg and the angle 9 be 25.0°. Find (a) the tension in the cord and (b) the normal force acting on the block. (c) If the cord is cut, find the magnitude of the block's acceleration. (a) Number 33.54 (b) Number 71.94 (c) Number -4.14 Units Units N m N Frictionless Units m/s^2 <

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 82A

See similar textbooks

Similar questions

I 00LLJ408 - Go.. Question Info and Solutions Blocks A and B of mass 5 kg and 10 kg respectively are placed on a Smooth inclined plane of Inclination 30, as shown. Block A and B are subjected to forces 5 N And 50 N respectively along the incline, as shown. The coefficient of friction between A andBis 0.50 find the frictional force between A and B in N is: (g= 10 ms SOH 300 Options Solution Fs=Static frictional force umg cos 30 (0.5) (5) (10) cos 30 21.6 N Let a be the acceleration of both the blocks along 5.27 PM
(a) Find the tension in each cable supporting the 588-N cat burglar. (Assume the angle θ of the inclined cable is 30.0°.) inclined cable N horizontal cable N vertical cable N (b) Suppose the horizontal cable were reattached higher up on the wall. Would the tension in the inclined cable increase, decrease, or stay the same?
A horizontal force is acting on a block moving on a rough horizontal surface. The force has the same magnitude ns the maximum fr rce of static frictica between the ' lock and the surfa e. If the coefficients of friction are Hs = %3D 0.75 and Hk = 0.50. Find the acceleration (in m/s?) of the block. 2.5 3.5 5.5 4.5 1.8
Determine the resultant ?R of the three tension forces acting on the eyt bolt. Find the magnitude of R and the angle θx which R makes with the positive x-axis. Note that F1= 563 N, F2= 345 N and F3= 296 N.
Draw the FBD of this problem.An object weighing 95 N is suspended by two wires, the left wire makes an angleof 37 0 with the vertical while the right wire is projected 26 0 with the horizontal.Find the tension in each wire.
A man is dragging a trunk up the loading ramp of a mover’s truck. The ramp has a slope angle of 20.0, and the man pulls upward with a force F S whose direction makes an angle of 30.0 with the ramp . (a) How large a force F S is necessary for the component Fx parallel to the ramp to be 90.0 N? (b) How large will the component Fy perpendicular to the ramp be then?
The coefficient of static friction between the block and the sloping plane is 0.38, and the coefficient of friction between the rope and the fixed cylindrical shaft is 0.11. Determine the range of values of P in newtons for which the 68 kg block does not move. (Enter the magnitude. Max force - Min force -
A persons head is bent over a book. The head weighs P=37.2 N and is supported by the muscle force Fm exerted by the neck extensor muscles and by the contact force Fc excerted at the atlantooccipital joint. Given that the magnitude of Fm is 60.0 N and is directed 35.0 degree below the horizontal. Find the direction of the contact force Fc. If the direction is below the horizontal, enter a negative value.
A student's head is bent over her physics book. The head weighs P = 25.6 N and is supported by the muscle force Fm exerted by the neck extensor muscles and by the contact force Fc exerted at the atlantooccipital joint. Given that the magnitude of Fm is 60.0 N and is directed 35.0° below the horizontal. PN Find the magnitude of the contact force F. . |N
A cable stretched between the fixed supports A and B is under a tension T of 2.3 kN. Express the tension as a vector using the unit vectors i and j, first, as a force TA acting on A and second, as a force Tg acting on B. 760 mm Α' 490 mm Answers: TA-i TB-i i+ i i+ i B j) kN j) kN
The base of an automobile jackstand forms an equilateral triangle of side length 12 in. and is centered under the collar A. Model the structure as one with a ball and socket at each joint and determine the force in members BC, BD, and CD. The forces are positive if in tension, negative if in compression. Neglect any horizontal reaction components under the feet B, C, and D. Assume F-700 lb, b-12 in., h-17 in. Answers: BC- i BD= i CD- i lb lb lb
400 N 30° 5. If the tension in the cable is 400 N, determine the magnitude and direction of the resultant force acting on the pulley. This angle is the same angle 0 of line AB on the tailboard block. 400 N