Referring to the figure below, the 60-N resistor absorbs an average power of 240 W. (a) Calculate the value of voltage, V (b) Determine the complex power of each branch of the circuit. (c) The overall complex power of the circuit? (Assume the current through the 60-N resistor has no phase shift.) 20Ω 30 Ω J20 Ω v (+ -j10 2 60 Ω

Referring to the figure below, the 60-N resistor absorbs an average power of 240 W. (a) Calculate the value of voltage, V (b) Determine the complex power of each branch of the circuit. (c) The overall complex power of the circuit? (Assume the current through the 60-N resistor has no phase shift.) 20Ω 30 Ω J20 Ω v (+ -j10 2 60 Ω

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter26: Three-phase Circuits

Section: Chapter Questions

Problem 3PA: You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a...

See similar textbooks

Similar questions

Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
A non-sinusoidal voltage eT=15+100sin1000t+75cos2000t- 50sin3000t volt is applied to the circuit shown in figure below, Compute the total dissipated power in the circuit. * iT ic İL 10MH 10µF
Assume that the load resistance can be varied between 0 and 4000 Ω andthat the capacitive reactance of the load can be varied between 0 and−2000 Ω. What settings of RL and XL transfer the most average powerto the load? What is the maximum average power that can be transferredunder these restrictions?
Determine the output waveform for the network of figure below and calculate the output dc level. Si D1 + 220 V 60 Hz ODeg 2.7kn V. TS POWER_10_Td_1 Si D2
Find the RMS value of V)-100 sin(377t+76) V
The variable resistor R in the circuit is adjusted until it absorbs the maximum average power. * The value of the maximum power transferred to the load is ..W ーj22 jl2 4/0° A 7.4 O 3.8 O 4.8 O none of the above 12,4 O
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
A2 KO resistor and 30 mH inductor are connected in series, across a 120 V A.C power source oscillating at 60 Hz frequency .Calculate i) The current in the circuit i) The voltage drop across the resistor & inductor ii) The power dissipated in the circuit. iv) The apparent power & reactive power in the circuit. v) Draw the phasor diagram.
5 The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? %3D C R eee V2 V3 23 V None of them 8.5 V 4.5V 37.5 V O 14.5 V
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.