Reorder the transfer function (shown below) using the values for the Black disk to the formHere C is just a constant.Q(s)KtVt(s) Rajs +Kt*Kb=Values for Black disk BelowRa = 25Kt = 0.0281Kb = 0.0312J= 3.248 x 10-5Had the answer correct which is =32.05310.9265 + 1Just step by step how to get the answerCTS + 1

Given a transfer function with below valuesRa = 25 Kt = 0.0281 Kb = 0.0312 J = 3.248 × 10-5 Reorder…

Reorder the transfer function (shown below) using the values for the Black disk to the form Here C is just a constant. Q(s) Vt(s) = Kt Rajs +Kt*Kb Values for Black disk Below Ra = 25 Kt = 0.0281 Kb = 0.0312 J = 3.248 x 10-5 Had the answer correct which is = 32.0531 0.9265 + 1 Just step by step how to get the answer C TS + 1

Reorder the transfer function (shown below) using the values for the Black disk to the form Here C is just a constant. Q(s) Vt(s) = Kt Rajs +Kt*Kb Values for Black disk Below Ra = 25 Kt = 0.0281 Kb = 0.0312 J = 3.248 x 10-5 Had the answer correct which is = 32.0531 0.9265 + 1 Just step by step how to get the answer C TS + 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8. At om Jemperatuse 300k ,pn junchion is us in eqů l86xium. hor which do ping concentrtion NA= 10%Cm, Na = 10T 10/08 2. asea A= 10t em %3D having cros8s lectiond find width of deple tion layer
b) If quantity A is PATAT with TC of 2mV/C, and quantity B is CTAT with TC of -1mVrC, then determine the following quantities if they are PTAT or CTAT 1. 1/A 2. 1/B 3. A+ 5°B
Which of the following(s) is(are) used in separation of ions in quadrupole analyzers? I. Electric field II. Magnetic field III. Metal rods Select one: a. I, II and III b. Only I c. II and III d. I and III e. I and II Plz do as soon as possible and explain briefly with correct explanation for +ve response
apoint chanay of 30ncis located at th corigam) while plane yz3 carries fined 1Dat point (6,4,3) chavg to nc /m'
1- 2- 3- 4- 5- s, True or False, and correct the error if there is. The solid-state relay depends on the electric field to control the output moving parts. At the solar cells, the long wavelengths generate electron-hole pairs at near the surface. The IMPATT is a noisy system because it depends on the avalanche break down. The BARITT diode depends on thermionic emission rather than avalanche multiplication. For IMPATT and BARITT microwave devices, the frequency generation is inversely proportional to the drift region length. 6- The Gun diode depends on the avalanche break down.
Determine:(a) Zin(b) Zo(c) Io if Vs=0.5mVp-p(d) Avs=Vo/Vs
This was a part of a solution set given to me in bartleby. I wanted to know if my speculations of this being miswritten is correct. The red indicates what i think should be a 0 and the blue indlcates what i think should be 1. if i am wrong please let me know how to understand the kmaps better?
Electrical Engineering Optical Communication Please full answers and clear. Explain and provide examples as necessary. I will put thumbs up. Explain why Ray theory is not sufficient to describe wave propagation in OFS What are the advantages and disadvantages of repeaters in OFS? What are the advantages and disadvantages of cladding in OFS?
8-The wave power per length is 1354 W/m, the device-width of the wave energy system is 6.3 m, the capture width ratio is 0.44, the rated power is 14379 W. Determine the percentage degree of utilization. O 26.10 O 23.49 O 22.19 O 28.71
What are em and he modes? How do they differ from te and tem modes? What is a single mode waveguide and why is it 0th order mode?
Sol the problem in image please ??
introduce the Behav?or OF the system with transfer Func+ion on the S 5s+ 6s +1O plane c FPnd the poles and 2eros) Ts=? Tr=? Td=? Tp =? %3D Wn =? % exceed = 2 %3D %3D