Required information Problem 10.041 - Steam power plant on the reheat Rankine cycle Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 74 percent and that of the pump is 95 percent. Problem 10.041.b - Temperature at the turbine exit Determine the quality (or temperature, if superheated) of the steam at the turbine exit. Use steam tables. The temperature of the steam at the turbine exit is 881 *C.

Required information Problem 10.041 - Steam power plant on the reheat Rankine cycle Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 74 percent and that of the pump is 95 percent. Problem 10.041.b - Temperature at the turbine exit Determine the quality (or temperature, if superheated) of the steam at the turbine exit. Use steam tables. The temperature of the steam at the turbine exit is 881 *C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the work done in the low-pressure turbine (LPT) of a Rankine cycle with reheat. The steam enters the LPT at 425°C & 60 MPa and leaves LPT as superheated steam at 375°C & 50MPA. Suggest what would be the dryness fraction of the working fluid entering the condenser.
The net work for a given reheat Rankine cycle is 80MW. Steam at 10 MPa and 500C enters the first turbine and then, the second turbine at 1.2 MPa and 500C. Saturated liquid exits the condenser at 20 kPa. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, point 4 at the reheater inlet, point 5 at the reheater outlet, and point 6 at the condenser inlet. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. IMPORTANT: USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY (uploaded already in the files section). Determine the following: Enthalpy at point 2 in kJ/kg = Enthalpy at point 4 in kJ/kg = Enthalpy at point 5 in kJ/kg = Enthalpy at point 6 in kJ/kg = Thermal Efficiency in % = Heat added in kJ/kg = Heat rejected in…
A Carnot power cycle uses water as the working fluid. The boiler operates at a pressure of 2000 kPa and the condenser operates at 100 kPa. Saturated water enters the boiler and saturated vapor leaves the boiler. a. Calculate the heat transfer in the boiler and the condenser as well as the useful work of the cycle. b. Calculate the useful work extracted from the turbine and the work spent on the pump c. Determine the efficiency of the cycle using the definition of the Carnot cycle as well as using the definition of thermodynamic cycles d. Calculate the process efficiency of the pump and the turbine.
Task (1) Consider a reheat Rankine cycle with a net power output of 100 MW. Steam enters the high pressure turbine at 10 MPa and 500°C and the low pressure turbine at 1 MPa and 500°C. The steam leaves the condenser at 10 kPa. The isentropic efficiencies of turbine and pump are 80% and 95%, respectively. Part 2 Discuss the need for superheated steam in a power generating plant while providing a T-S diagram to show the difference in the amount of Wnet in the cycle. Part 3 Explain why the Rankine cycle is preferred over the Carnot cycle in steam power plants while constructing a T-S diagram for both Rankine and Carnot cycles to demonstrate the difference.
52 es ! Check my work Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 82 percent and that of the pump is 95 percent. Determine the quality (or temperature, if superheated) of the steam at the turbine exit. Use steam tables. (You must provide an answer before moving on to the next part.) The temperature of the steam at the turbine exit is 109.42 °C.
A ideal rankine power plant cycle uses ammonia as the working fluid.Saturated vapor leaves the boiler at a temperature of 85 o C. The condenser temperatureis 40 o C. Calculate the heat transfer to the boiler, the work done by the turbine, and thethermal efficiency of the cycle.
In an ideal reheat-regenerative cycle, steam enters the turbine at 6 MPaa and 400°C. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300°C. Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.01MPaa. Use mass flowrate of 1 kg/s.
10-1 to 10-2 Carnot and Rankine Cycles A simple ideal Rankine cycle that uses water as the working fluid operates its condenser at 30°C and its boiler at 250°C. Calculate the work produced by the turbine, the heat supplied in the boiler, and the thermal efficiency of this cycle when the steam enters the turbine without any superheating. Use steam tables.
4) In a reheat Rankine cycle, water vapor enters the high-pressure turbine at 9MPa and 450°C. It is expanded to an intermediate pressure of 0.8MPa and enters the low-pressure turbine with a temperature of 400°C. Condenser pressure is 7.5kPa and water enters the pump as a saturated liquid. There is no pressure loss in the piping that connects the cycle components. Water mass flow rate is 60 kg/s and both turbines have an isentropic efficiency of 90%. Calculate mankan kunne tħe b) net power output, in MW
4) In a reheat Rankine cycle, water vapor enters the high-pressure turbine at 9MPa and 450°C. It is expanded to an intermediate pressure of 0.8MPa and enters the low-pressure turbine with a temperature of 400°C. Condenser pressure is 7.5kPa and water enters the pump as a saturated liquid. There is no pressure loss in the piping that connects the cycle components. Water mass flow rate is 60 kg/s and both turbines have an isentropic efficiency of 90%. Calculate c) thermal efficiency of the cycle. (
In a reheat-regenerative Rankine cycle, the condenser pressure is 10 KPa. Steam enters the first turbine at 12.5 MPa and 500 oC. Steam is reheated at 3 MPa at the same temperature before entering the second turbine. For the regeneration, steam is extracted from the second turbine at 0.5 MPa to an open feedwater heater (OFWH). Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the 1st pump (right after the condenser) outlet, point 3 at the OFWH outlet, point 4 at the 2nd pump outlet, point 5 at the boiler outlet, point 6 at the reheater inlet, point 7 at the reheater outlet, point 8 for the extraction of steam to OFWH and point 9 at the condenser inlet. Use 2 decimal places for the enthalpy, steam quality (%), thermal efficiency (%), and other energies. For the fraction of steam (y) and entropy (s), use 4 decimal places. For the specific volume, use 6 decimal places. IMPORTANT: USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY…
QUESTION 3 An ideal reheat Rankine cycle with water as the working fluid operates the boiler at 15 MPa, the reheater at 1,200 kPa, and the condenser at 10 kPa. Figure 2 shows the schematic of the cycle in sequential order. The temperature is 550 °C at the entrance of the high pressure (High-P) and low pressure (Low-P) turbines. If the mass flow rate through the cycle is 3 kg/s. For eycle; i) sketch T-s diagram, ii) calculate the enthalpy (h) value at all indicated locations in the Figure 2, iii) determine the net power produced by the cycle, iv) determine the rate of heat transfer into the cycle, and v) evaluate the thermal efficiency of this system. High-P turbine Low-P turbine Reheater Boiler Condenser Pump Figure 2