Rod AB is made of a steel for which the yield strength is ay 450 MPa and E= 200 GPa: rod BC is made of an aluminum alloy for which gy-280 MPa and E-73 GPa. Determine the maximum strain energy that can be acquired by the composite rod ABC without causing any permanent deformations. Given: dag 8.5 mm and dac=15.5 mm. 1.6 m dac da 4 energy Lean be acquired by the composite rod ABC without causing any permanent deformations is 136.69 The maximum

Rod AB is made of a steel for which the yield strength is ay 450 MPa and E= 200 GPa: rod BC is made of an aluminum alloy for which gy-280 MPa and E-73 GPa. Determine the maximum strain energy that can be acquired by the composite rod ABC without causing any permanent deformations. Given: dag 8.5 mm and dac=15.5 mm. 1.6 m dac da 4 energy Lean be acquired by the composite rod ABC without causing any permanent deformations is 136.69 The maximum

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.1P: An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a)...

See similar textbooks

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?
CEM BOGA 27°C Mostly sunny Q1. Determine the maximum strain energy that can be acquired by the composite rod ABC without causing any permanent deformations. Rod AB is made of a Structural Steel (ASTM- A36), rod BC is made of an Aluminum Alloy (2024-T4). A 1.5 m B 10-mm diameter Search 1.8 m 14-mm diameter 1/1 000 W 3
Determine the change in length, width and thickness of steel bar which is 4m long, 30mm wide and 20mm thick and is subjected to an axial pull of 30 kN in the direction of length. Take E = 200 GPa and poison's ratio of 0.3. Also determine the volumetric strain and change in volume.
A part is subjected to uniaxial compression stress of 40 MPa in the x- direction ( -40MPA). If the material's elastic modulus (E) is 100 GPa and Poisson's ratio is 0.35. What are the strains in the y-direction and z- direction? Eyy = 0.00014, ɛ zz = 0.007 %3D O Eyy 0.00014, E zz 0.00014 Eyy = -0.00014, ɛ zz -0.00014 O Eyy -0.002, ɛzz = -0.006 %3| ||
A load of P = 3.1 kip is applied to the A-36 structural- steel beam. The modulus of elastisity and shear modulus for A-36 steel are 29 (103)ksi and 11(103) ksi respectively. (Figure 1) Figure 3 ft 12 in. 4 ft- B 2 in. 1 of 1 TAL 12 in. 41 6 in. Determine the strain & at point A. Express your answer using three significant figures. Ex 11 Submit ▾ Part B IVD ΑΣΦ | Π Try Request Answer Determine the shear strain Yay at point A. Express your answer using three significant figures. Submit ΠΑΣΦΗ 11 vec Request Answer vec ? ?
The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm andagagelengthof50.8mm.IfaloadofP=60kNisapplied to the specimen, determine its new diameter and length. Take n = 0.35.
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F. Select one: O F = 5236 N O F = 6283 N %3D O F= 13090N O F = 10472 N O F= 15708N OF=4189 N 9:22 PM EN ? 4/15/2021