Show that the following function may be used as an Airy stress function+ = Ar + Br²y + CxyEvaluate A, B and C for the rectangle shown in Figure Q3:(1) there are no external loads for any kind applied along KN;(2) along KL there is a uniform normal load p;(3) and along MN there is no normal load;(4) along KL, LM and MN there are shear stresses (but none along KN).Make a neat sketch of the stresses along the boundary KLMN.NMThickness=1p per unit lengtha

Answered: Image /qna-images/answer/8afd2157-0296-45da-a7c6-e432786b8ed9.jpg

Answered: Show that the following function may be…

Engineering

Civil Engineering

Show that the following function may be used as an Airy stress function + = Ax? + Br?y + Cry

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Sxy

Q: Determine maximum shear stress

A: To determine the maximum shear stress. The maximum shear stress is equal to one-half the…

Q: Two blocks of wood, 55 mm deep and 30 mm thick are glued together as shown. Determine the normal…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Cross section of each bar 350 mm2 . Find stress in bar CD

Q: ट ६६ docs.google.com The state of plane stress at a point is represented on the element shown in the…

Q: Determine principal stress and maximum shear stress

A: Given data : Normal stress in X direction (σX)=50 MPaNormal stress in Y direction (σY)=10 MPaShear…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: The principal stresses at a point in a bar are 160 N/mm² (tensile) and 80 N/mm² (compr.). The…

Q: Given the following principal stresses and principal direction: ox = 27 MPa, oy = 15 MPa, txy = 6…

Q: 3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A…

A: A member subjected to pull is given and it has been asked to determine normal and shear stress…

Q: Determine the axial stress acting on a circular column. *

A: Axial Stress- Axial stresses are those which are responsible for bringing a change to the length of…

Q: For the element below, determine, a) Principal stresses b) Orientation of Principal stress planes c)…

Q: Discuss Computation of Effective Stresses

A: Basic concepts- Effective Stress- Effective stress is a parameter in soil that is responsible for…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Given:- Sx=26 MPaSy=75 MPaSxy=10 MPa

Q: Question 1 - Combined Stresses Given in figure 1, stub column with dimensions a, b and wall…

Q: 0/Derive the double armature 1. equation. As stress As

Q: According to Saint-Venant’s principle, the actual stress distribution at the support is highly…

A: Saint Venant's Principle:

Q: b = 331 E = 186 KN.m. M = 6.5 KN.m. 420mm 1. Calculate the maximum tensile and compressive strength.…

Q: (e) Compute the flexural stresses. Compressive stress of concrete at the top of the beam and tensile…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Define the following a) Flexure stress b) Flexural rigidity c) Neutral axis/surface

A: When a beam is subjected to bending moment it sags or hogs. When it sags fibres at the bottom are…

Q: QUESTION 11 What is the magnitude of the maximum shear stress at the critical location? If none,…

Q: Determine the stress at locations A, B, C, D, E and F (Figure 2). Show step by step

A: Consider the figure shown below.

Q: Question 3 If the stresses on two perpendicular planes through a point are 60 N/mm? tension, 40…

A: Stresses acting at a plane 60° to the tensile stress is calculated by using the relation,…

Q: PA 1.875 in. 0.75 in. 0.125 in. 1.25 in. r = 0.25 in. On the figure above, clearly mark with an "X"…

A: Stress Concentration - The max. stress accumulated or applied within a structural element is called…

Q: Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: The cross section of a concrete corner column that is loaded uniformly in compression is shown in…

A: The pressure that deforms the material in order to reduce the volume of the material is the…

Q: What will be max. height that the water tank that will become full if the max. tangential stress is…

Q: 982. The strain components at a given point are e = -533 x 10-", e, = 67 x 10", and 0.30, find the…

A: Given data : εx = - 533 × 10-6εy = 67 × 10-6τxy = -626 × 10-6E =30 ×106v = 0.30θ = 45° The…

Q: What will be max. height that the water tank that may become full if the max. tangential stress is…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Describe the term alpha in total stress method.

A: Piles in clay generally carry most of the load by virtue of skin friction.

Q: Given the following principal stresses and principal direction: ơx = 27 MPa, oy = 15 MPa, txy = 6…

Q: Describe about the Total Stress Method.

A: At any given plane section in the soil mass total stress is defined as the sum of the self weight of…

Q: A wood beam is reinforced with steel straps at its top and bottom as shown. Determine the maximum…

A: modular ratio: m=ESTEW=21015=14 Convert steel into wood: BSteel =14×200=2800 mm

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Q1) For the loading shown, determine the stress at (a) point A. (b) point B. В 200 100 F

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: principal stresses. The strains measured in these respectively. E = 2.1 x 10 N/mm? and Poisson's In…

Q: Determine stress value

A: This question is related with solid mechanics . In this question we are provided with value of…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Given stresses at the points are SX = 52 Mpa (tensile) Sy = 63 Mpa(tensile) And shear stress Sxy =…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: For the state of plane stress shown, determine (a) the principal stresses and maximum in-plane…

A: The give data is: σx=48 MPaσy=60 MPaσxy=-100 MPa

Q: Current Attempt in Progress Consider a point in a structural member that is subjected to plane…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: (1) ld. What is the shear stress on an element with principal stresses of 565 psi and -435 psi?

Q: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled, find the…

A: The given data is: σx=16 MPaσy=9 MPaτxy=5 MPa ccw

Q: What can the beam shear stress equation that was derived in Sec. 5.8 be used to calculate? O the…

Q: Plot mohr cirvle to find principal stresses Stress in Y direction 0

A: solution If we draw the stress element the diagram would be stress in X direction =389.5Mpa…

Concept explainers

Planar Stresses

Question

100%

Show that the following function may be used as an Airy stress function
+ = Ar + Br²y + Cxy
Evaluate A, B and C for the rectangle shown in Figure Q3:
(1) there are no external loads for any kind applied along KN;
(2) along KL there is a uniform normal load p;
(3) and along MN there is no normal load;
(4) along KL, LM and MN there are shear stresses (but none along KN).
Make a neat sketch of the stresses along the boundary KLMN.
N
M
Thickness=1
p per unit length
a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 2 continue

Step 2 continue

Step 3

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Plane stress state is given on a material element as shown below. Os1-a+b+h T1=27 (MPa), on=b+c+d+h (MPa), ti2=c+g+h+d (MPa), O"=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate stresses (normal and shear) on AB surface. b) Find principal stress values and their directions (w/ respect to normal n of the AB surface). ) Find maximum in-plane shear stress and its direction (w/ respect to normal n of the AB surface). d) Find the volumetric and distortion strain energy densities at this point. 011=17 022=20 112= 14
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
Find A. Minor stress B. Normal stress acting on plane AB C. Shear stress acting on plane AB
Plot mohr cirvle to find principal stresses Stress in Y direction 0
A stat of stress is specified in figure by using Mohr's circle determine the normal and shearing GPI. GP2 stresses on (a) the principal plane, (b) the planes of maximum shearing stress and sketch the ERST resulting elements. 400 MPa 250 MPa 560 MPa
2D stress at a point is given by a matrix 100 301 = [1 30 20 shear stress in MPa is Oxx Txy Tyx Oyy The maximum MPa
Question 7 The bronze bar 3 m long with a cross-sectional area of 350 mm? is placed between two rigid walls. At a temperature of -20°C, there is a gap A = 2.2 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18.0 x 106 /°C and E = 80 GPa. 3 m-
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B; = 0.8 m; B; = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
The bronze bar 5 m long with a cross sectional area of 425 mm² is placed between two rigid walls as shown in the Figure. At a temperature of -20°C, the gap A = 3.8 mm. Find the temperature at which the compressive stress in the bar will be 35 MPa. Use a = 18.0 x 10-6 m/(m-°C) and E = 80 GPa. L A
At a point in a stressed material the stress components are: Ox= -30, Oyy = 75, 1 = 72, Tyz = 40, 0 = 110 T= 30, all are in MPa Calculate the normal, shear and resultant stresses on a plane whose normal makes an angle of 40° with the x axis and 60° with the y-axis.
A state of stress is specified in the figure shown below. Determine the Normal stress o (mPa) on the Principal Plane if P1 = -63 mPa; P2 = -80 mPa and v= 54 mPa Py Px
Find the value of stress Force=2 N Area 2 mm2