Situation 3: As shown in the figure block D is used tosupport the 100-kg uniform pole. ABC in the position shown..1.2.3.7.5 m-A=0.2-3 m--0.2.D11C4 m.Find the normal force at point B.Find the frictional force at point B.Calculate the weight of the lightest block D than can be.used to support the pole against impending sliding..

Answered: Image /qna-images/answer/a90fe660-6d9b-49d2-b4db-2c7b979978f9.jpg

Situation 3: As shown in the figure block D is used to support the 100-kg uniform pole. ABC in the position shown.. - SL B A=0.2 -3 m- -0.2. D 11 C . 4 m 1. Find the normal force at point B. Find the frictional force at point B. 2. 3. Calculate the weight of the lightest block D than can be. used to support the pole against impending sliding.

Situation 3: As shown in the figure block D is used to support the 100-kg uniform pole. ABC in the position shown.. - SL B A=0.2 -3 m- -0.2. D 11 C . 4 m 1. Find the normal force at point B. Find the frictional force at point B. 2. 3. Calculate the weight of the lightest block D than can be. used to support the pole against impending sliding.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m
F2 =300 N F1 F=700 N 60 м, -1500 Nm 2 m 3m For the above diagram, given that F, = 450 N, 8 = 30 degrees and d = 4 m, calculate the following (neglect the depth of the beam). Note that there is a pin support at A and a roller support at B. The magnitude of the resultant of the applied forces, FR. Please provide the answer in kilo Newtons and report to three significant figures. Please include the unit ("kN") within your answer (e.g. if the calculated answer was 55.562 Newtons please input 55.6 kN). Answer: The angle between the resultant force, FRand the negative x axis (measured anti clockwise from the negative x axis). Please provide the answer in degrees and report to three significant figures. Please include the unit ("deg") within your answer (e.g. if the calculated answer was 55.562 degrees please input: 55.6 deg). Answer: Locate the resultant force, FR, so that it is equivalent to the system of applied forces. Calculate the offset distance of the resultant force, FR, measured…
PROBLEM 5: In the figure shown below, u = 0.3 for all contact surface. ma = 150 kg, mb = 200 kg P B 40 a. If e = 0, find P for motion to impend to the right. b. If e = 0, find P to just prevent the motion.
1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is represented by the 2 kN load shown. a. Produce shear and moment diagrams for the supporting frame ABC. b. Calculate the horizontal deflection of the point of loading. Assume that frame ABC has bending stiffness El = 2.7×105 Nm². 0.9 m A 0.6 m C B 2 KN
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. What is the displacement of the loaded end B of the bar in mm? Neglect deflections of the bar due to bending. Use E=200 GPa. = 2.6 m a b = 2.1 m c = 1.2 m w = 62 kN с 36 mme B
Question 3 T/2 A 1200 Nm A homogeneous steel shaft (G=83GPA) loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member AB. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 10 psi for the plastic, and neglect the deformation of the steel frame. A 3 ft B 2 ft Plastic sheet 2.
The uniform 2200-lb bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 0.165 in2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 10.6 x 106 psi for aluminum. 6 ft A В 10 ft C
The 679-N force is applied to the 114-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.77 = 0.60 Answer: F= i 26° N P = 679 N
125 kN 125 kN (1) 4.2 m 175 kN 175 kN 5.0 m A The roof and second floor of a building are supported by the column shown. The structural steel (E=200 GPa) column has a constant cross-sectional area of 5000 mm?. Determine the following: The force between BC (FBc) is equal to in kN: The force between AB (FAB) is equal to in kN: The deflection of Joint C relative to Joint B is equal to in mm: The deflection of Joint A relative to Joint B is equal to in mm: The total deflection of Joint C relative to foundation A in mm: B.
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
24KN/m 12KN/m Зт A simply supported beam is loaded as shown in the figure. Assume El is constant. Determine: a. The reaction at the roller support in kN. b. The deflection at point "B" in terms of El. The deflection at the midspan in terms of El. C.