Situation No. 2 Given: An 80% stress grade Guijo has an allowable bending stress of 21.8 MPa, E = 8.47 x 103 MPa, compression parallel to grain is 13.2 Mpa. The beam dimension is 150 mm x 450 mm. It carries a concentrated load at the center. Span of the beam is 7 m. Solve for the allowable bending stress.

Situation No. 2 Given: An 80% stress grade Guijo has an allowable bending stress of 21.8 MPa, E = 8.47 x 103 MPa, compression parallel to grain is 13.2 Mpa. The beam dimension is 150 mm x 450 mm. It carries a concentrated load at the center. Span of the beam is 7 m. Solve for the allowable bending stress.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
A beam is reinforced for tension only unless its required steel ratio is _________ the maximum steel ratio required by NSCP 2015. Select one: a. greater b. smaller If the strain in the compression bar is less than that of the yield strain, is the value of fy equal to fs'? Select one: a. no b. yes
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
A small aluminum alloy [E 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a 165 mm. The cross- sectional dimensions of the tee shape are b 19 mm, d= 29 mm, and t 7 mm, After loads are applied to the beam at B, C, and D,a compressive normal strain of 480 uɛ is measured from a strain gage located at c=5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 17 P. P. 3P Strain gage D a - H. a b. Answer: ! N P = i 2.
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are $x = 32 MPa, Sy= 79 MPa, and Sxy= 28 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sxy