State the control goal.Identify the input and output variables for the process.Identify the controlled variable(s); manipulated variable(s).iv.lii.Define the following terminologies as used in control systems: -a. Controlled variableb. Manipulated variablec. Disturbance variabled. Set-point 1. Figure 1 below shows a stirred tank heating process-with a constant holdup volume.Assume mass flow rate w, of the inlet pipe is constant whereas its temperature Tfluctuates but the product temperature T must be maintained within set temperaturetolerances about the reference.HeaterFigure 1: Stirred heating tank process

Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

State the control goal. Identify the input and output variables for the process. Identify the controlled variable(s); manipulated variable(s). iv. Define the following terminologies as used in control systems: a. Controlled variable b. Manipulated variable C. Disturbance variable d. Set-point

State the control goal. Identify the input and output variables for the process. Identify the controlled variable(s); manipulated variable(s). iv. Define the following terminologies as used in control systems: a. Controlled variable b. Manipulated variable C. Disturbance variable d. Set-point

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
3 Condenser Expansion valve Compressor Evaporator Tin ļ Tout Fig.2: Heat pump system described in part (a) [2] 1. Construct a P-h and T-S plots showing a. All the processes b. The refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR).
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar what is the pressure in bar at state 4 to 3 decimal places? what is the specific entropy in kJ/kg-K for state 5 to 4 d.p.?
Exampie Air conditioning unit uses Freon R-22 for conditioned office at 25 C. The evaporating temperature is 17 C and the condensing temperature is 47 C. The compressor is reciprocating and single acting with number of cylinders of 4, volumetric efficiency of 0.9, number of revolution is 900 rpm cylinder dimensions of L/D is 1.25. If the compressor power is 3 kW and mechanical efficiency of 0.9, estimate the followings: the refrigerant mass flow rate in kg/min, refrigeration capacity in TR, cylinder dimensions, condenser heat load, coefficient of performance and relative efficiency. and
Condenser 30 c „Flash Chamber Pi Evaporator OC & 50 kW For a 2-stage ammonia compression system, determine: 1. Draw the PH diagram showing the condenser, evaporator, & compressor discharge temps, intercooler pressure, all enthalpies & compressor suction specific volumes, m/kg 2. Compute the intercooler pressure in Bars & equivalent Ti in °C 3. Compressor discharge temps T: & T4 4. Mass of refrigerants m:, ms & m: in kg/sec 5. Compressor power Wi, W & total W- in kW & HP 6. Compressors PD with equal volumetric efficiency 80%; m/s 7. Condenser capacity, kW 8. Using a single stage compression, calculate & compare the power of the compressor/s in kW & HP
steam enters the steam generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5kg/s. Find the percentage increase in volume (%) due to drying and superheating.
8.3 A four-effect evaporator is being considered for concentratinga fruit juice that has no appreciable boiling-point elevation.Steam is available at 143.27 kPa, and the boiling point ofthe product in the fourth effect is 45°C. The overall heat-transfer coeffi cients are 3000 W/(m 2 °C) in the fi rst effect,2500W/(m2 °C) in the second effect, 2100W/(m2°C) in thethird effect, and 1800W/(m2°C) in the fourth effect. Calculatethe boiling-point temperatures of the product in the fi rst,second, and third effects. Assume the heating areas in all theeffects are equal to 50m2 each. The mass fl ow rate of steam tothe fi rst effect is 2400kg/h, the feed rate to the fi rst effect of 5%total solids fl uid is 15,000kg/h, the concentrated product fromthe fi rst effect leaves at 6.25% total solids, and the concentrationof product leaving the second effect is 8.82% total solids. Make it in the form of a spreadsheet for solving the example problem no. 8.2 and 8.3
7. A pan made of stainless steel contains water at atmospheric pressure. The pan diameter is 25 cm and its surface is mechanically polished. The pan is now heated while its surface is maintained at 116 C. Find the surface heat flux, the boil off (evaporation) rate, and the peak heat flux
b) The high pressure units on a steam plant operate at 10bar (gauge), and the condensate is sub-cooled by 9.5K. If the mass flow rate of condensate is 10 kg/s, use the provided steam tables to determine how much saturated steam at 1.5 bar this condensate could produce. Note it is sufficiently accurate for high pressure condensate, as in this question, to assume that the specific enthalpy is the same as for the saturated liquid at the same temperature.