Steam at a pressure of 0.08 bar and a quality of 87.4% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 3.4 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater Mi kg/h

Steam at a pressure of 0.08 bar and a quality of 87.4% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 3.4 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater Mi kg/h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two products enter an indirect contact heat exchanger that uses steam for heating. The first product which contains 12% solids enters at the rate of 3 kg/hr and at 10 °C. The second stream which contains 20% solids enters at the rate of 4 kg/hr and at 20 °C. Saturated steam at 150 °C (hL = 2745.9 kJ/kg, hv = 632.25 k.J/kg) enters the heat exchanger at 0.5 kg/hr with a quality of 95% and exits at 10% quality. The resulting mixture enters an indirect contact cooler. Water enters the indirect contact cooler at a temperature of 10 °C and exits at 25 °C. Two product streams exit the cooler. The first stream contains 24% solids and exits at 2 kg/hr and at 10 °C, while the second stream exits at 12 °C. The specific heat of the solids is 3500 J/kg K and that of water is 4180 J/kg K. Complete/label the process diagram and determine the following: a. Specific heat of each stream b. Enthalpy of entering and exiting steam c. Temperature of the mixture exiting the indirect contact heat exchanger,…
Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of 20 kPa and 95% dryness. In the condenser, there is heat transfer to the river water flowing through the pipes. The temperature rise of the river water is limited to 10 ° C to prevent thermal pollution. Since the state of the water at the condenser outlet is a saturated liquid at 20 kPa pressure, what is the flow rate of the cooling water?
A heat exchanger is used to heat 36 kg/hr of air originally at standard conditions (25 °C and 1 atm) to 125 °C using steam originally at 10 bar and 300 °C. Assume both streams maintain constant pressure and air to be an ideal gas with constant cp = 1.005 kJ/kg·K. No heat is lostto the surroundings. Calculate: The minimum flow rate of the steam in kg/hr?
Exhaust steam from an engine passes into a condenser at a pressure of 0.12 bar and dryness 0.88. The temperature of the condensate from the condenser is 40°C. The circulating water enters the condenser at 12°C and leaves at 29°C. Calculate the mass of circulating water per kg steam condensed. Steam Properties: Steam at 0.12 bar (0.012 MPa) hf = 207 kJ/kg hfg = 2383 kJ/kg Water Properties Water at 40°C Water at 29°C Water at 12°C h = 167.5 kJ/kg h = 121.5 kJ/kg h = 50.4 kJ/kg A. 26.71 kg B. 28.05 kg C. 30.04 kg D. 32.86 kg
A steam with 45 atm and 90 degrees Celsius (enthalpy = 2500 kJ/kg) enter a heat exchanger. Water also enter this exchanger at 5 atm and 10 degrees Celsius (enthalpy = 250 kJ/kg). Both have a mass flow rate of 1 kg/s and 100% steam quality. What are the pressure and temperature values of the exiting stream?
Thermodynamics A water is heat up by heat exchanger at a rate of 0.16 kg/s from 24 to 70 °C. Geothermal water (cp=4.25 kJ/kg °C) available at 140 °C at a mass flow rate of 0.5 kg/s will be used for heating. Determine the geothermal water exit temperature.
Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of 20 kPa and a dryness degree of 95 percent. In the condenser, there is heat transfer to the river water flowing through the pipes. The temperature rise of the river water is limited to 10 C to prevent thermal pollution. Since the state of the water at the condenser outlet is saturated liquid at 20 kPa pressure, what should be the flow rate of the cooling water.
Hot air at 400°C and 150 kPa is to be used to produce saturated steam at 200°C in an insulated, non-mixing heat exchanger. Water enters the heat exchanger at 20°C while the air leaves at 350°C. The mass flow rate of air is 0.8 kg/s, pressure drops are negligible, and specific heats for air are evaluated at the average air temperature.What is the mass flow rate of water, in kg/s. Report your answer to four decimal places using rounding.
A refrigerator with tetrafluoroethane as refrigerant operates with an evaporation temperature of −25°C and a condensation temperature of 26°C. Saturated liquid refrigerant from the condenser flows through an expansion valve into the evaporator, from which it emerges as saturated vapor. (a) For a cooling rate of 5 kJ·s−1, what is the circulation rate of the refrigerant? (b) By how much would the circulation rate be reduced if the throttle valve were replaced by a turbine in which the refrigerant expands isentropically?
Refrigerant (known as R-134a) enters a heat exchanger at 100 kPa. The refrigerant is of 20% quality upon entering. It exits the heat exchanger as a saturated vapor also at 100kPa. An unknown liquid (specific heat capacity of 3.9 kJ/Kg.K) enters the heat exchanger at a rate of 1.1 kg/sec at 320.15 Kelvin. This unknown liquid exits at 278.15 degrees kelvin. Find: The mass flow rate or the refrigerant [kg/sec]Q (the rate of heat transfer)
In general, heat exchangers with higher flow rates have greater capacities?
Saturated propane vapor at 2:00 x 102 psia is fed to a well-insulated heat exchanger at a rate of 3:00 x 103 SCFH (standard cubic feet per hour). The propane leaves the exchanger as a saturated liquid (i.e., a liquid at its boiling point) at the same pressure. Cooling water enters the exchanger at70°F, flowing cocurrently (in the same direction) with the propane. The temperature difference between the outlet streams (liquid propane and water) is 15°F.(a) What is the outlet temperature of the water stream? (Use the Antoine equation.) Is the outlet water temperature less than or greater than the outlet propane temperature? Briefly explain.(b) Estimate the rate (Btu/h) at which heat must be transferred from the propane to the water in the heat exchanger and the required flow rate (lbm/h) of the water. (You will need to write two separate energy balances.) Assume the heat capacity of liquid water is constant at 1.00 Btu/(lb m°F) and neglect heat losses to the outside and the effects of…