Step 2) Find the optimum value of the reheat pressure in order to achieve the highest efficiency in the domain of the admissible values of the steam quality. For that keep the turbine inlet conditions as given. Cycle 2- Idcal Rankine Cycle With Reheating Pick out four different values of the reheat pressure within the interval (0.1 to 0.4) x inlet pressure to high pressure turbine, to find the proper reheat pressure. Procced as follows: Case I. Keep the turbine exit pressure the same as the one obtained in step 1 for the highest efficiency at x = 0.87. Change the reheat pressure to obtain the best efficiency. Casc I.

Step 2) Find the optimum value of the reheat pressure in order to achieve the highest efficiency in the domain of the admissible values of the steam quality. For that keep the turbine inlet conditions as given. Cycle 2- Idcal Rankine Cycle With Reheating Pick out four different values of the reheat pressure within the interval (0.1 to 0.4) x inlet pressure to high pressure turbine, to find the proper reheat pressure. Procced as follows: Case I. Keep the turbine exit pressure the same as the one obtained in step 1 for the highest efficiency at x = 0.87. Change the reheat pressure to obtain the best efficiency. Casc I.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

I'll leave a thumbs up if you ans the following. Determine the following: a. The fuel flow rate in kg/sec b. Cooling water flow rate in kg/min c. Assume an ideal cycle with pump efficiency = 80% and turbine efficiency = 85%, find the quality of steam entering the condenser
Homework-2 Compute the themal e fficiency of an ideal Ran kine cycle for which the steam leavea the boiler as Saturated Vapor at 30 bars. The turbine-outlet Conditions is Be1 bar. Determine the mass floo rate of the steam in kg/hr, net Power output of the cycle is 50000 Sehematic ond given data are: 1f the kw. The TI= 5002 P 3०bars %3D 9in (saturated) vapour 30 bars 2 PR =0-1 bar 4 Pa=30 bas o-1 bar +4 Tout 3 (Saturated liquid) Wp ( Simple Ideal Power cycle) (T.S. diagram e)
Give example of a problem solved using reheat rankine cycle method and compare to rankine cycle method
Cycle effeciency isn't 68% and use variable spec heat formulas
a steam 8.0 mpa and 485 degrees celsius enter the turbine and expand at condenser pressure of 0.006 mpa for cycle and 1kg of steam. determine heat added, worknet, thermal efficienc, for the engine determine steam flow for an engine output of 40000 kw, work turbine, energy chargable, ideal heat rate
Example problem of reheat cycle
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
Consider a 10:1 pressure rise in the ideal compressor with air as the working fluid compared to the a pump with water as the working fluid and the same pressure rise and same inlet pressure. Check all that apply The compreesor takes 300 times more work/unit mass as the pump The work per unit mass is about the same between the two. Becase the pump deals iwth a liquid the work will be higher. The compressor in a Brayton cycle has a much greater effect on performance than a pump in a Rankine cycle.
Gas compression and expansionSketch the cycle as well as determine the Qcycle and Q31 in kj
i need some one explian the TS digram Rankine Cycle
Show given, complete solution, and diagram. A steam power plant operates on the Rankine Cycle. The steam enters the turbine at 7 Mpa and 550 with a velocity of 30 m/s. It discharges to the condenser at 20kpa with a velocity at 90 m/s. Calculate the net workin kw for a flow of 37.8kg/s. a. 23.23 Mw c. 34.22 Mw b. 53.34 Mw d. 46.54 Mw
At 10kPa pressure and dryness degree x=0.90, the steam coming out of the turbine goes to the pump with adiabatic efficiency of 0.85 after condensing in the condenser. The pump sends the condensed water to the steam boiler with a working pressure of 8MPa. a) Find the h.T values of the inlet points of the condenser, pump and boiler b) Since the flow rate of the condensed water is 9000 kg/h, find the load of the condenser c) Find the power of the pump