telephone 9.17 A three-phase, 60-Hz, power line is supported on a horizontal crossarm, and the separation distance between adjacent conductors is 2 m. The current flowing in the conductors is 100 A. A telephone line is supported on a horizontal crossarm that is placed 1.5 m below the power line, and the telephone wires are 1 m apart. Find the expression for the mutual inductance between the power line and the telephone line. Calculate the induced voltage per kilometer in the telephone line.

telephone 9.17 A three-phase, 60-Hz, power line is supported on a horizontal crossarm, and the separation distance between adjacent conductors is 2 m. The current flowing in the conductors is 100 A. A telephone line is supported on a horizontal crossarm that is placed 1.5 m below the power line, and the telephone wires are 1 m apart. Find the expression for the mutual inductance between the power line and the telephone line. Calculate the induced voltage per kilometer in the telephone line.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
Compare alternative and direct currents by comparing their physical properties. (Explain alternans, cycles, periods, frequency terms during this comparison. Also in this comparison, explain the electron flow directions separately in alternating and direct current)
1-Choose the correct statement for pure resistor connected across single phase AC supply. a. Current and Voltage are in phase b. Current leads the supply voltage by 90° c. None of these d. Current lags the supply voltage by 90° 2-Identify the current through the inductor in a RL transient circuit connected across DC voltage, when the switch is kept open. a. 0 b. Infinity c. V/R d. 1
2) C. When the capacitor is fully charged, the top conductor while the bottom conductor D. Electric field lines are and a potential difference is E. The capacitance of a capacitor is defined as F. The unit of capacitance is
Q5. Describe the properties of ferromagnetic materials.
A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
3. For a parallel circuit of 20 ohms resistor and a 10 ohms inductor, is connected to a 110/60 cps Volts source a) find the Impedance b) determine current IR c) determine the current IL d) find the inductance.
give definition and explanation about Capacitance meter
7. Each of three insulators forming a string has self-capacitance of "C farad. The shunt capacitance of each cap of msulator is 0 25 C to earth and 0-15 C to line. Calculate the voltage distribution across each insulator as a pecentage of line voltage to earth and the string efficiency.
GENERAL RLC CIRCUITS: Solve and show your solution completely. Make sure your answers are in 4 decimals places. The ohmic resistance of a large magnetic contactor is measured to be 20 ohms. A 230 V 60 Hzis impressed upon the contactor and the current is taken as 3.2 amperes. Neglecting core loss,determine the inductance of the contactor in mH.
Question A suspension type insulator has three units with self-capacitance C and ground capacitance 0.1C. What will be the string efficiency?
A 120 V, 60 W lamp is to be operated on 220 V, 50 Hz supply mains. For the lamp to operate in correct voltage, calculate the value of (i) non-inductive resistance and (ii) pure inductance (U.P.T.U. 2005–06)