The 6.3-kg block A has an initial speed of 6.17 m/s as it slides down the smooth ramp, after which it collides with the stationary block B of mass 9.36 kg. If the two blocks couple together after collision, determine their common velocity in m/s immediately after collision. h = 1.86 m A'

The 6.3-kg block A has an initial speed of 6.17 m/s as it slides down the smooth ramp, after which it collides with the stationary block B of mass 9.36 kg. If the two blocks couple together after collision, determine their common velocity in m/s immediately after collision. h = 1.86 m A'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Design of Tension Members annel shape is used as ember. The channels are

Q: The pressure drop in a 30 cm diameter horizontal pipe is 60 kPa in a distance of 15 m. The wall…

Q: Thelower column has across section of 17.5 cm and an axial load of P-75 kN. Ifthe size of one side…

A: Area of cross section of lower column = 17.5 cm2 or 1750 mm2 Load = 75 KN or 75000 KN

Q: Three tanks problem Example (13) (60.00) (30.00) B Qi Q2 Pipe Length diameter J 1500 m 300 mm AJ BJ…

A: Given :

Q: A laminate which is composed of 4 layers of unidirectional glass fibres with stacking sequence of…

Q: Situation: Using Three-Moment Equation. Determine the following. El is Constant.

A: Given data:

Q: Problem # 6: The figure shows a roof truss and the detail of connection at joint I. The allowable…

Q: (a) Explain the following terms with reference to frequency studies: (i) Annual series (ii) Partial…

Q: Once you finish overlaying layers pertaining to all requested parameters, you can proceed to find…

A: ArcGIS:ArcGIS family of client software, server software, and online Geographic Information System…

Q: tively. Assuming that the flood series follow Gumbel's distribution, determine the flood magnitudes…

Q: Discussion: - 1. Does the distance travelled by the center of gravity of the Maxwell's disc depend…

Q: A 470-mm-diameter, non-slender, spiral column is symmetrically reinforced with 8-20 mm vertical…

A: Answer:-

Q: trapezoidal as defined below and conveys a discharge of 200 cfs. Use the standard step method. 1 n =…

A: Given n= 0.030 S= 0.0050

Q: DETERMINE THE LARGEST LOADP THAT CAN BE APPLIED TO THE BARS OF THE LAP JOINT SHOWN IN THE FIGURE.…

Q: The annual floods of a river at a particular site were analysed by Gumbel's method which yielded Q =…

Q: The design storm for a basin has the depth of rainfall for successive hours as 5.6, 7.6 and 5.2 cm.…

Q: simply supported beam 300 mm wide, 500 mm deep and spans 5.9 m supports a service super imposed dead…

Q: ee of freedom - formulate th mm² and E=20

Q: 1) Determine the force P that will give the block shown an acceleration of 2.5 m/s² . f= 0.26 0 =…

Q: Problem - 05 An ascending gradient 1 in 60 meets a descending gradient 1 in 50. Find the length of…

Q: Solve for r- by = 450 mm Ie = 20 mm comprentice fange 83.33 compression web z-E --z 3 83.33 20 = 20…

Q: 3. Determine elevations (3 decimals) on the tangents at: a) sta. 136+ 111 b) sta. 136+321 G) sta.…

A: The grade of back tangent, g1 =-3.7%The grade of forward tangent, g2 =+0.9%The elevation of station…

Q: W FF 0= 18° 006, AR 0 = 18°

Q: A new spar buoy, 0.5 m diameter, is being designed to carry oceanographic instrumen- tation in the…

A: It is possible that you may be startled to hear that our findings in the preceding example do not…

Q: Consider a system where a horizontal, laminar, separated flow of air and water at 100 kPa pressure…

A: Motivation. The preparation, presentation, and interpretation of experimental findings are covered…

Q: 1m 10 kN 5 kN/m 2m 2m- 4m A beam with a hinge is loaded as above. Draw the shear force and bending…

Q: A curve having tangents of UV and VW intersects at point V. UV and VW has an azimuth (from south) of…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: 2. A trust rum d a solid right Craular Gne has an axjal hole of so Cm diameter as shown in figure.…

Q: Fill up tabele#1 below to calculate exact quantity of cach given item as given in figure#1 & #2…

A: Calculate the total centerline length L as given as, L=4.3-0.125+6.5-0.125+5=15.55 m 1) Item…

Q: The beam shown below has a cross section of channel shape with width b-D200 mm and height h=80 mm,…

Q: Question 2: A one-story shear building with an appendage attached to its top is subject to a…

Q: A BLOCK OF WOOD 0.20 m THICK IS FLOATING IN SEA WATER. THE SPECIFIC GRAVITY OF WOOD IS 0.65 WHILE…

A: Weight of man, wm = 50*9.81= 490.5 N Weight of wood ww = 0.65*9810*(0.2*A) =1275.3A And, buoyancy…

Q: A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 – 28 mm deformed…

A: Answer we are given f'c = 49 Mpa fy = 362 Mpa As = 4- 28 mm bars As = 4 * π4*282 As = 2463 mm2 We…

Q: 2 Con vation depths (in feet) are shown for each corner. grid shown. Existing exca- 2.6 50 ft 3.3 50…

Q: 1) CALCULATE THE MAGNITUDE OF THE RESULTANT FORCE PER METER LENGTH DUE TO WATER ACTING ON THE RADIAL…

A: Given data, Radius r = 6 m

Q: 1. The required reactor detention time, 0. 2. The reactor basin volume, V, in m³. 3. The net waste…

Q: Determine the horizontal and vertical components of force that the pins A and B exert on the…

Q: 26 kN 7 kN/ m 0.7 m. 0.6 m 3 0.8 m 12 kN/ m 0.4 m

Q: simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead…

Q: S The following are the values of righting levers, in metres, at various angles of inclination for a…

Q: The difference in elevation between the surface of the water in a storage reservoir and the intake…

Q: The beam shown, شت تار وان( 3V a. draw sFD and BMD, b. prove that for the isosceles:, Gmax. = oh E…

Q: 3. Specify the type of compound truss and determine the force members in JH, BJ, and BI. State if…

Q: Problem # 5: The figure shows a roof truss and the detail of connection at joint I. The allowable…

A: Given allowable stresses for shear = 70 MPa, for bearing = 135 MPa…

Q: 1. A 340 x 660mm beam is to carry a 660KNm load using concrete and steel with strengths of 21MPa and…

Q: A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 8-ϕ25 mm equally…

A: We have to determine the nominal axial strength of the column in kN as per the given data in the…

Q: A certain cable, 504.76 ft long is suspended between two supports at the same elevation and 500 ft…

A: When assessing the structural health and safety of cable-stayed bridges, cable tension is a vital…

Q: Determine the horizontal and vertical components of reaction at the supports A and C. Assume the…

Q: 6

Q: Find the value of strain if stress is 50 MPa and youngs modulus is 100 MPa

A: The strain can be calculated using Hookes law.

Question

The 6.3-kg block A has an
initial speed of 6.17 m/s as it
slides down the smooth
ramp, after which it collides
with the stationary block B of
mass 9.36 kg. If the two
blocks couple together after
collision, determine their
common velocity in m/s
immediately after collision.
h = 1.86 m
A
5
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. Determine the reactions at A and B when a = 150 mm. 500 N 240 mm В ATVS
Unit 4 Rotation Gravity, Satellites... An Fw-10200 N vehicle is stalled one-third of the way across a bridge Compute the support force Fsup that needs to be supplied at the support of the bridge farthest from the vehicle.
团の image.jpg > B00 Deker mine the magni nde mnd direction 200 of the resultant +300 of the four forces shown in the higure. 420 500 Determine the moment a bout Point as Shown
w = N/m wL 764EI Omax at x = 0.475L
b) Wire AB suspends a load of 268 N at Point B. Determine the magnitude of the force P required to maintain equilibrium for the system shown in Figure Q1b when wire AB is at an angle of 57⁰. A 57⁰ P B 268 N
Ans (P) - 50.4KN need explanation
F224006 F3=60016 f1%=700lb 30° Detremine the magnitude of the resultant force acting on the corbel and its direction 0 measured counterclockwise from the x axis.
Determine the resultant of B and C if the resultant of A and B is 100 kN directed along the z-axis.
What is the Vertical Reaction at A in kN? [add negative (-) sign if answer is to the left / downwards]
I. For the frame shown (AN 15), the force F acting upward at C causes a horizontal reaction of 100 kN at C. Which of the following most nearly gives 1) The value of the force F in kN, 2) gives the reaction at A in kN, 3) the angle in degrees that the reaction at A makes with the horizontal axis (positive counterclockwise). 5 m Figure AN-15
6 RN m 10KN 50° Am 5 KNn 22 3 3 * 关 FIND THE REACTION FORCES OF THE SUPPORIFO BEAM
What is the Horizontal Reaction at A in kN? [add negative (-) sign if answer is to the left / downwards]