The 66-kg man with center of mass G supports the 33-kg drum as shown. Find the greatest distancex at which the man can positionhimself without slipping if the coefficient of static friction between his shoes and the ground is 0.45.5.6 m33 kg66 kg0.9 mAnswer:x = iE

Given that , Mass of man m=66kg Mass of drummd=33kgStatic frictionμs=0.45

The 66-kg man with center of mass G supports the 33-kg drum as shown. Find the greatest distancex at which the man can positio himself without slipping if the coefficient of static friction between his shoes and the ground is 0.45. 5.6 m 33 kg 66 kg 0.9 m Answer:x = i E

The 66-kg man with center of mass G supports the 33-kg drum as shown. Find the greatest distancex at which the man can positio himself without slipping if the coefficient of static friction between his shoes and the ground is 0.45. 5.6 m 33 kg 66 kg 0.9 m Answer:x = i E

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.23P: The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of...

See similar textbooks

Related questions

Q: Calculate the tangential stress in the steel.

A: Calculate the tangential stress in the steel.

Q: Determine the velocity and frequency of vibration of a rope 6 m long with a mass of 2 kg and…

Q: Determine the value of n.

A: To find value n

Q: Determine the mobility and the number of idle degrees of freedom associated with each mechanism Show…

Q: A diesel engine works on the dual combustion cycle and has a compression ratio of 18. At the start…

Q: A single extraction turbine operates on an ideal regenerative cycle, pressure and temperature…

A: To find

Q: 6% of the stroke. State 1 is defined by 14psia and 140°F. For the hot-air standard with k=1.34 and…

Q: A 3-m-wide, 8-m-high rectangular gate CD is located at the end of a rectangular passage that is…

A: A plate is subjected to a fluid pressure distributed over its surface when exposed to fluid. In most…

Q: Following is not the assumption of Bernoulli Energy Equation

A: option B is the correct answer

Q: Propane is a hydrocarbon that burns to produce carbon dioxide or carbon monoxide, depending on the…

Q: The Reynolds number for the fluid flow through a pipeline is estimated as 1250. The Darcy Weisbach…

Q: N =3x2-2y4,Given that the standard uncertainties of I and y are u(r) and u(y).then the correct…

A: Correct answer: option (C)

Q: Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.11 sq.in.…

Q: Compare the thermal efficiency and turbine-exit quality at the condenser pressure for a simple…

A: Answer: (a) Net work done: 1293.35 kJ/kg. (b)Thermal efficiency: 35.865 %. (c) Turbine exit quality…

Q: 10.25 For a flow rate of 12 L/s and turbine speed of 65 rpm, estimate the power transferred from the…

Q: The system is made up of the 1-m, 8.0-kg uniform rod AB and the two uniform disks (each of 0.17 m…

Q: Uniform internal heat generation at q =6.0×10^7 W/m3 is occurring in a cylindrical nuclear reactor…

A: Given, Internal rate of heat generation = q˙g = 6 x 107 W/m3 Diameter of fuel rod = d = 60 mm…

Q: Apply an energy balance on a turbine and then suggest two (2) ways to increase the power output of a…

A: Energy equation for steady state condition is written and two ways are suggested to increase power…

Q: 1. In the figure shown below, two blocks are connected by a solid strut attached to each block with…

A: find the minimum weight of A to prevent motion.

Q: How does a heat exchanger work? Where and when will you use a heat exchanger?

A: A heat exchanger is a device in which heat is transferred from one fluid to another. Working:- In…

Q: What are the general sources of error when using Vernier Caliper? when using Micrometer Caliper?

Q: For the circular thin plate with a square hole as shown in the image below, its radius R = 0.42 m…

Q: Determine the y-coordinate of the centroid of the shaded area.

Q: How can you apply the concept of linear combination in engineering

A: Given question: How can you apply the concept of linear combination in engineering?

Q: T(t) 1 N-m/rad 02(1) to 1 N-m/rad 1 kg-m2 1 N-m-s/rad 1 N-m-s/rad 1 ANSWER: G(s): 2s2 +s+ 1 The…

Q: A mass of 5 kg of saturated water vapor at 300 kPa is heated at constant pressure until the…

Q: Determine the forces at the pin joint (F) ? and the roller support (G)

Q: Determine the maximum shearing stress and elongation in a bronze helical spring composed of 15 turns…

Q: For the beam and loading shown, determine the minimum required width b, knowing that for the grade…

Q: Wet steam at 200°C and 20% moisture is compressed in an irreversible adiabatic process to a process…

Q: Water flows through a circular tube with a velocity of 2 m/s. The diameter of the pipe is 14 cm If…

Q: Q3) A constant volume fuel air cycle with a compression ratio of 8, the A/F=15:1. The pressure…

Q: During a quasi-equilibrium process, the pressure- volume relationship follows the function below: P…

A: a= -1200 kPa/m^3 b= 600 kPa Pressure volume relationship: ⇒P= aV+b⇒P= -1200V+600 Initial volume, V1=…

Q: A spherical pressure vessel has a 1.33-ft inner radius and 0.19-in. wall thickness. If the working…

A: Radius, r= 1.33 ft= 15.96 in Hence, diameter, d= 2r= 2(15.96)= 31.92 in Thickness, t= 0.19 in…

Q: The roof of an airconditioned home is 7 m long, 9 m wide, and 20 cm thick. It is made of a flat…

A: find the cost of electricity.

Q: 3) A single-pass tubular type heat exchanger heats air from 35 C to 80 C. Exhaust gas from DIESEL…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A Carnot engine operating between 775 K and 305 K produces 54 kJ of work. Determine (a) QA, (b) Qr…

Q: 9. The submerged, curve surface AB in figure below is one quarter of a circle of radius 4 ft. The…

Q: Determine the reactions at A and C

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

Q: The single slider mechanism shown below has the following dimensions: the crank AB = 95 mm and the…

Q: A train weighing 120 tons is pulled up a 2% grade. The train resistance is constant at 12 lb/ton.…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: + REMEDIAL ACTIVITY FOR MODULE 2_MEC30-2_3Q_2122 Question 17 of 27 -/ 20 E : View Policies Current…

A: find the value P.

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

Q: nt of inertia about the x-axis for (a) h = 0 and (b) h = 5 in. h i in.4 y = i in.4

A: find the moment of inertia about x-axis.

Q: I- If a rigid body undergoing planar motion, it has at most II- Second moment of force (F.r) is…

A: To find :- Fill in the blanks

Q: Which of the following head is neglected in ideal Bernoulli's Energy equation 1. Head loss due…

A: Bernoulli's equation is nothing but another version of conservation of energy

Q: Steam enters the first turbine stage of a vapor power cycle with reheat and regeneration at 32 MPa,…

A: Answer: consider the enthalpies of each stage in the cycle as follows: h1 = h@ 32MPa,600°C = 3423.8…

Q: 2.25 The hydranlie eylinder BD eerts on member ABC a force P directed along line BD. Kowing that P…

A: Given Load, F = 750 N Angle = 60o Find Magnitude, P Force component

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.

Question

The 66-kg man with center of mass G supports the 33-kg drum as shown. Find the greatest distancex at which the man can position
himself without slipping if the coefficient of static friction between his shoes and the ground is 0.45.
5.6 m
33 kg
66 kg
0.9 m
Answer:x = i
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide. (The car pulling the crate is analyzed in Prob. 7.19.)
The 320-lb homogeneous spool is placed on the inclined surface. Determine the vertical force P that is required to keep the spool in the position shown. Assume that there is enough friction to prevent slipping at A.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The panel of weight W with its center of gravity at G is placed between vertical guides and released. Determine the largest height h for which the panel will not slide down due to binding at corners A and B. The coefficient of static friction between the panel and the guides is 0.5.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.