subject (solid 2)use this matrix num (AD200153)pls show me full steps with clear handwriting sirpls answer in 20 mins sir B6 m3 mFigure Q3 The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm ( X is a last digit ofyour matrix number) and is used as a strut to support the beam. The yield strength of materialis oy = 260 MPa. Take modulus of elasticity, Es = 210 GPa.(a) Determine the maximum intensity w of the uniform distributed load that can be appliedto the beam without causing the strut to buckle. Take factor of safety = 3 againstbuckling. Check whether Euler's equation is appropriate or not.(b) Then, calculate the new maximum intensity w if end condition for strut both fixed.

(a) Write the given data. d=5X=53 mmσY=260 MPaEs=210 GPaFOS=3

The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm ( X is a last digit of your matrix number) and is used as a strut to support the beam. The yield strength of material is oy = 260 MPa. Take modulus of elasticity, E, = 210 GPa. (a) Determine the maximum intensity w of the uniform distributed load that can be applied to the beam without causing the strut to buckle. Take factor of safety = 3 against buckling. Check whether Euler's equation is appropriate or not. (b) Then, calculate the new maximum intensity w if end condition for strut both fixed.

The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm ( X is a last digit of your matrix number) and is used as a strut to support the beam. The yield strength of material is oy = 260 MPa. Take modulus of elasticity, E, = 210 GPa. (a) Determine the maximum intensity w of the uniform distributed load that can be applied to the beam without causing the strut to buckle. Take factor of safety = 3 against buckling. Check whether Euler's equation is appropriate or not. (b) Then, calculate the new maximum intensity w if end condition for strut both fixed.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.4P: A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to...

See similar textbooks

Similar questions

Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A brass cube of 48 mm on each edge is comp ressed in two perpendicular directions by forces P = 160 kN (see figure). (a) Calculate the change ...IV in the volume of the cube and the strain energy U stored in the cube. assuming E = 100 GPa and i’ = 0.34. (b) Repeat part (a) if the cube is made of an alumim um alloy with E = 73 GPa and v = 0.33.
The nonprismalic cantilever circular bar shown has an internal cylindrical hole of diameter dtl From 0 to x so the net area of the cross section n for segment I is A. Load P is applied at x, and load Ptl is applied at x = L. Assume that E is constant. (a) Find reaction force Ry (b) Find internal axial forces Ntin segments I and 2. (c} Find .v required to obtain axial displacement at joint 3 of
A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
A solid steel sphere (E = 210 GPa, v = 0.3) is subjected to hydrostatic pressure p such that its volume is reduced by 0.4%. (a) Calculate the pressure p. (b) Calculate the volume modulus of elasticity K for the steel. (c) Calculate the strain energy U stored in the sphere jilts diameter is d = 150 mm.
Wires B and C are attached to a support at the left-hand end and to a pin-supported rigid bar at the right-hand end (see figure). Each wire has cross-sectional area A =0.03 in2 and modulus of elasticity E = 30 X 106 psi. When the bar is in a vertical position, the length of each wire is L = 80 in. However, before being attached to the bar, the length of wire B was 79.98 in. and wire C was 79.95 in. Find the tensile forces TBand Tc in the wires under the action of a force P = 700 lb acting at the upper end of the bar.
A circular aluminum alloy bar of length L = 1.8 m has a slot in the middle half of its length (see figure). The bar has a radius r = 36 mm and modulus of elasticity E = 72 GPa. The slot has a height 2a = r/4. Calculate the elongation of the bar due to forces P applied at the ends if the axial stress in the middle region is known to be 180 MPa.
A thin metal strip of total weight W and length L is placed across the top of a flat table of width L2as shown in the figure. What is the clearance S between the strip and the middle of the table? (The strip of metal has flexural rigidity EI.)
Repeat Problem 2.4-8, but assume that the bar is made of aluminum alloy and that BC is prismatic. Assume that P = 20 kim. L = 3 ft.t = 314 in., b1 2m.b 2.Sin.andElO.400ksi.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.