Quiz 07.pdf →Note: Answer All QuestionsQ1The access door is held in the 30° open position by the chain AB. If thetension in the chain is 180 N, determine the projection of the tension forceonto the diagonal axis CD of the door.B.| 900|mm900 mm1200 mm30Q2The uniform 7-m steel shaft has a mass of 200 kg and is supported by a balland-socket joint at A in the horizontal floor. The ball end B rests against thesmooth vertical walls, but one of the vertical walls supporting end B isturned through a 36° angle as shown. Compute the forces exerted by thewalls and the floor on the ends of the shaft.

Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

The access door is held in the 30 open position by the chain AB. If the tension in the chain is 180 N, determine the projection of the tension force onto the diagonal axis CD of the door. B 1900 |mm 900 mm D 1200 mm AC 30

The access door is held in the 30 open position by the chain AB. If the tension in the chain is 180 N, determine the projection of the tension force onto the diagonal axis CD of the door. B 1900 |mm 900 mm D 1200 mm AC 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a mechanism that raises packages in a transfer mechanism. A 500-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank 02A and the force in member AB The weights of the links are negligible. 30mm 450mm 500N 220 mm B 374 mm 374 mm The angular velocity of the link O,BD in rad/s is = The magnitude of the velocity of point D in m/s is =
Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
L2 L3 D B. L4 L5 L6 Find the magnitude of the force exerted on bolt E, given: P = 85 lbs, L1 = 0.5 in, L2 = 4.5 in, L3 = 1.4 in, L4 = 3.1 in, L5 = 1.4 in, L6 = 1.9 in, L7 = 0.9 in, L8 = 0.2 in Ey = Number Ibs (enter a positive number)
Part A When y is zero, the springs sustain a force of 54 lb . (Figure 1) Determine the magnitude of the applied vertical forces F and -F required to pull point A away from point Ba distance of y = 1.5 ft . The ends of cords CAD and CBD are attached to rings at Cand D. Express your answer to two significant figures and include the appropriate units. Figure 1 of 1 ? F = Value Units Submit Request Answer 2 ft 2ft k = 40 lb/ft www k = 40 lb/ft 2 ft Provide Feedback Next > 6 2 ft O
Activity 1. The points B, C and D of the cantilever frame are attached to a vertical wall. The 500 N load is parallel to the z-axis, and the 1,500 N load is vertical. Compute the force in each member. 3m 500N 2m 4m 1500N Activity 2. The tripod shown supports a load P = 1500 N. Compute the force in each leg of the tripod. |1500 N B 6m 4m 2m
The figure shows a mechanism that raises packages in a transfer mechanism. A 200-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 287 rpm CCW. At the position shown the crank OA is vertical and the output link OB is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. 50mm 450mm 200 N 200 mm B. 374 mm 300mm X The angular velocity of the link OĄBD in rad/s is = Choose... + The magnitude of the velocity of point D in m/s is = Choose... + The torque required from the motor at the crank O2A in N.m is = Choose... : The force in member AB in N is = Choose... +
PART 2: Determine whether the given mechanisms are Grashof's Chain, Non- Grashof's Chain or Transition chain using Grashof's criterion. Show your solution. 1. If: AB = 25 cm BC = 43 cm CD = 45 cm AD = 50 cm 2. If: AB = 1 ft BC = 1.8 ft CD = 2.4 ft AD = 3.5 ft D 3. If: AB = 6 in BC = 13.2 in CD = 21.1 in AD = 25.7 in
DRAW THE FREE BODY DIAGRAM OF THE FOLLOWING PROBLEMS PROBLEMS 3.1 Block A has a mass of 160 kg and is supported by the flexible cables B and C. Draw the free body diagram of A. 0.5m Prob.3.1 +48 1450N 0.5m 1.Om A 30° 2.5m 780 N Prob.3.2 Prob.3.3 3.2 The vertical bar A has a mass of 100 kg. Draw the free body diagram of A assuming that all surfaces of contact are smooth. 3.3 The 30-kg bar A is supported by a smooth pin at one end and by a flexible cable at the other end. Draw the free body diagram of the bar.
Find the torque on link 2 necessary to maintain static equilibrium for the 4-bar mechanism shown below. Use analytical method, draw free body diagram of each link. O,A = 3.5 in., AB = 0,B = 6 in., O,C = 7 in. P.=50 lb 4 -152. 105 240° M12 2
Part A 6 ft Ax= -106.7 lb, Ay = 80.0 lb Ax= -46.7 lb, Ay = 45.0 lb == Ax-53.3 lb, Ay = 40.0 lb Ax = 13.3 lb, Ay 10.0 lb O Ax O O Ax -4 ft 4 ft- 0.5 ft Determine the horizontal and vertical components of force at pin A. 80 lb B
Determine the horizontal and vertical components of force at pin A. O Ax=-46.7 lb, Ay = 45.0 lb O Ax = 13.3 lb, Ay = 10.0 lb O Ax=-53.3 lb, Ay = 40.0 lb O Ax= -106.7 lb, Ay = 80.0 lb 6 ft -4 ft- 0.5 ft 80 1b4 4 ft-
One end of a uniform 2.60m rod with a mass of 38.0kg is supported by a cable connecting one end to the wall so that the cable makes an angle of 42.0° with respect to the rod. The other end rests against the vertical wall, where it is held in place by friction so that the rod is perfectly horizontal. A sign with an unknown mass is hung from the rod 1.90m from the wall so that wall exerts a normal force of 1790N on the rod in the positive x-direction. What is the mass of the sign in kilograms?