The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of the weld CANNOT exceed 3in. If the weld must transmit a total force equal to 9600 lb, it's size should be

The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of the weld CANNOT exceed 3in. If the weld must transmit a total force equal to 9600 lb, it's size should be

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.3P: Use an elastic analysis and determine the maximum load per inch of weld.

See similar textbooks

Related questions

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A: To Determine Largest allowable gauge pressure, P

Q: A high-strength steel band saw, 30 mm wide, runs over pulleys 1100 mm in diameter. What minimum…

A: Given data, E = 230 GPa Width = 30 mm Flexural stress = 290 MPa Diameter over pulley = 1100 mm To…

Q: Comection Deta / CE A572- 65 2.0" TM 1" Thick 1.5h 1-5" 1.5" 1.5 3 TM RIGID BAR 6' 7' What is the…

A: Given Data: The diameter of the bolts is d=5/8 in. The grade of the bolts is A325. Consider only the…

Q: find the inside diameter of the pipe

A: Internal Diameter = 59.61 mm

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 1100 mm in diameter. What minimum…

Q: 10.7 The shearing force at a given section of a built-up I-girder is 1000 kN and the depth of the…

Q: B. What force is required to punch a square hole shear strength is 350 MNm2. (25-mm 25mm) in a plate…

A: The punching force can be found out by using following relationship: Force (F)=Hole…

Q: The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a…

A: 125 mm -124.7 mm=0.3 =0.0003m average normal stress in each post:

Q: The screw in the illustration is subjected to a 10kN force represented by the red arrows. If the…

A: Considering normal stress:σallow=PA70mpa=20×1000Nπ4d2d=19.07mm≈20mm

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 700 mm in diameter. What minimum…

Q: The 16-foot solid steel shaft has been twisted 4 times. Determine the diameter d of the shaft if the…

A: ASKED: To determine the diameter of the solid circular shaft. Given, Length of the shaft (L) = 16…

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: ζb=70 MPaζs=110 MPaGb=80 GPaGs=40 GPa di=70 mmd0=90 mm

Q: The two vertical rods attached to the light rigid bar are identical except for ength. Before the…

Q: Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A: Given a rod consisting of two cylindrical portions as shown below AB is made up of steel, with Es…

Q: 4. A steel supplier lists rectangular steel tubing having outside dimensions of 4 by 2 in. and a…

A: We need to find Torque and angle of twist please check the answer below.

Q: 2. Determine the lengths of the side fillet welds required at the heel and toe of the angle shown.…

A: Given shear stress in weld = 124 MPa For plate thickness 13 mm minimum size of weld =5 mmand…

Q: The allowable stresses for the splice shown below are the following: 150 MPa. for shear of rivets,…

Q: A high-strength steel band saw, 23 mm wide, runs over pulleys 800 mm in diameter. What minimum…

Q: 60 KN A BLOCK SHOWN IS SUBJECTED TO A TRIAXIAL LOADING OF THREE 40 mm UNIFORMLY DISTRIBUTED FORCES.…

A: As per guidelines we need to answer only 1st 3 subparts of the question.

Q: A compound girder consists of a 45 cm by 18 cm steel joist, of weight 1000 N/m, with a steel plate…

A: The given data is: Allowable longitudinal stress in plates=110 MN/m2 Allowable shearing stress in…

Q: steel bar is attached to a wood support beam with four 20 mm diameter lag screws, as shown in the…

A: Given : Dia of lag screws = 20 mm width of steel bar = 60 mm and thickness = 5 mm yield strength =…

Q: A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter…

A: Bearing strength is the maximum stress load that the unit can hold before the structure fails. But…

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

A: Given data in question UDL Point load Span member length Cross section To find out Bending…

Q: 4. A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A…

Q: A high-strength steel band saw, 26 mm wide, runs over pulleys 1200 mm in diameter. What minimum…

Q: 6. The round bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross…

Q: onal member, a single angle 76 mm x 76 mm x 6 mm with a m² is welded to an 8 mm thick gusset plate.…

Q: A flanged bolt coupling consists of six 12-mm-diameter steel bolts (Gst = 80 GPa) on a bolt circle…

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: Given:- ζball = 70 MPaζsall = 110 MPaGs = 80 GPaGb = 40 GPadi = d = 70 mm, d0 = 90 mm…

Q: A high-strength steel band saw, 24 mm wide, runs over pulleys 900 mm in diameter. What minimum…

A: Given: Steel band width = 24mm Diameter of pulley = 900 mm Flexural stress = 380 mm, E = 210 GPa…

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN…

Q: A plate is attached to the frame of a machine by two side fillet welds as shown. Determine the…

A: Welding is a manufacture interaction by which at least two sections are combined through hotness,…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Q: nated wood beam giuing (actual dimensions) cross section, as shown int 12 in. 3 in. 2 in. 2 in. 2…

Q: 8.5 A welded connection of steel plates is shown in Fig. 8.76. It is subjected to an eccentric force…

A: Given, Allowable shear stress = 70 N/mm2 eccentric force = 50 kN

Q: 2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial…

A: Cross-section of steel bar = 0.55x4.05 in2 Thickness (t) = 0.55 inBreadth (b) = 4.05 inLoad P = 30.5…

Q: A double U-shaped butt weld is to connect two plates 200 mm (d) x 20 mm (b), as shown in the given…

Q: he allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: Given data, a = 3.2 in b = 3.6 in d = 10.8 in t = 0.4 in V = 39 kips To Find out the shear flow…

Q: Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to…

A: To determine the minimum effective length for given weld size. Given, Weld size = 5/8 in. As per…

Q: The cylindrical portion of the compressed air tank shown is fabricated of 0.25-in.-thick plate…

A: Calculation of inner radius- r=d2-tr=102-0.5r=4.75 in

Q: A high-strength steel band saw, 25 mm wide, runs over pulleys 700 mm in diameter. What minimum…

Q: A plate is connected to the column using fillet welds as shown. The size of weld is 8 mm. Determine…

Q: A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six…

A: Given data, For a single unequal angle 100x75 is connected to a 10 mm thick gusset plate at the ends…

Q: A flanged bolt coupling consists of seven 0.75-in. diameter aluminum bolts on a bolt circle 13-in.…

A: The given data is shown below: Diameter of aluminium bolts=0.75 in.Number of aluminium…

Q: The plate shown in the figure is fastened to the fixed member by seven 10-mm-diameter rivets.…

A: Given :

Concept explainers

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.

Question

A. 1/2 in.

B. 3/8 in.

C. 5/16 in.

D. 1/4 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the safe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit stress in shear is 13,600 psi? A. 8650 lb B. 9420 lb C. 10,500 lb D. 11,800 lb
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal 9600 lbs, its size should be
Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.
2. Determine the lengths of the side fillet welds required at the heel and toe of the angle shown. Allowable shearing stress through the throat of each weld is 124 MPa. L 150 x 150 x 13 L1 P1 108 13 150 mm T= 250 kN P21 L2 gusset plate 150
Determine the lengths of the side fillet welds required at the heel and toe of the angle shown. Allowable shearing stress through the throat of each weld is 124 MPa. L 150 x 150 x 13 L1 P1 108 T= 250 kN 42 13 150 mm P2+ L2 gusset plate 150
A flanged bolt coupling consists of six 1/2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 9000 psi in the steel or 6000 psi in the aluminum? Assume Gst = 12 x 10^6 psi and Gal = 4 x 10^6 psi.
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 16 ksi. O 480 psi O 305 psi O 376 psi O 407 psi 523 psi
1. Refer to the sketch below. a. What type of joint is shown? b. What type of weld is shown? C. Is the weld in shear or normal stress? d. Calculate the magnitude of stress in the weld. K /P= 50 Kip /P = 50 Kip 10" I 1/4"
S Example 8.7 An ISA 200x100x10 angle LO 3 is welded to a steel plate by means of fillet welds as shown in Fig. 8.17. The angle is subjected to a static force of 150 kN and the permissible shear stress for the weld is 70 N/mm². Determine the lengths of weld at the top and bottom. 1₁ 150 kN TAILL Y2 200 12 - IG 100- 12 71.8 150 KN -10