The assembly consists of two red brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stain less 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The part ist fix at both ends (A, C and F) Determine: a. The reaction force at point A, Cand F b. The deflection of point B, E, D The average normal stress develoned in rods AB CD and FF

The assembly consists of two red brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stain less 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The part ist fix at both ends (A, C and F) Determine: a. The reaction force at point A, Cand F b. The deflection of point B, E, D The average normal stress develoned in rods AB CD and FF

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: A cantilever beam of length 1m carries a point load of 1900N at the free end. The cross-section of…

A: Given data:- length of cantilever beam, L=1 m Point load, P=1900 N Dimension of cross-section of…

Q: Nonprismatic Beams veered cantilever beam AB of length L has square cross sections and supports a…

Q: The shaft shown consists of a steel tube (1) bonded to a brass core (2). The shear modulus of steel…

Q: pressure is de only för the stat at is no dynamic component as no motion is involved 2

A: Total pressure does not depends on dynamic component but it only depends on static fluid at rest

Q: The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: For the given bell crank:

Q: A rigid bar DAB is supported by two circular rods and a pin as shown below. The member at D is an…

A: Equations of equilibrium : ∑MA=0650×250-FBC×150-FD×150=01083-FBC-FD=0…

Q: Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA,…

Q: F14-11. Determine the principal stresses at point A on the cross section of the beam at section a-a.…

A: Principal stresses at 'A' :Shear force Vmax=30 kNMoment max Mmax=300.3=9 KNmI=50150312⇒I=14062500…

Q: F13-3. Determine the state of stress at point A on the cross section of the beam at section a-a.…

A: Given: The state of stress at point A on the cross section of the beam is to be determined. Show the…

Q: 022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown.…

Q: Problem 3: Put 32.5 into a steel tube 2.4 meters long, 34 mm radius and 1.5 mm thick. A circular bar…

A: Given, T= 900 Nm GS = 77 GPa GA= 26 GPa radius of steel = 34 mm thickness = 1.5 mm

Q: Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal…

A: Given Data: The allowable normal stress for the material is, σallow=200 MPa The expression for the…

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: The solid shaft is used to transmit the torque shown. If the absolute maximum shear stress allowed…

A: Given: The absolute maximum shear stress is 25.5 MPa. The maximum angle of twist is 0.025 rad. The…

Q: Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1)…

A: Strain is the result of a material's deformation due to stress. It's only a proportion of the length…

Q: A flat steel bar, 25mm wide by 6mm thick and 1 m long, is bent by couple applied at the ends so that…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

Q: Supports A and B of the pin-ended column shown are at a fixed dis-tance L from each other. Knowing…

A: Given: Supports A and B of the column are pin-ended Distance between the two ends is L

Q: E oth ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T…

Q: -) The 150-mm-diameter rods AB and BC, having the original lengths shown, are joined at the collar B…

A: step 1-

Q: After a load P = 150KN is applied to the pin-connected structure shown, the temperature increases…

A: Given:- The magnitude of the load = P = 150 kN The temperature increases = 100°C The thermal…

Q: 2. The stepped steel shaft camies the torque T. Determine the maximum allowable magnitude of T if…

A: Finding out maximum torque required in shaft.

Q: 1. A rigid bar AN is hinged at A and is supported by a rod CD at C. The rod is pin connected at D.…

A: Given data in question Load Span member length Elasticity modulus Diameter To find out Stress…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Q: he bell-crank mechanism shown in Figure P1.33 is in equilibrium for an applied load of P = 7 kN at…

A: P= 4kN ; a= 200mm ; b=140mm ; c=6mm; t=10mm θ=65°and shear stress=40 Mpa The expression for moment…

Q: 3. A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is slipped over a solid…

Q: Three steel rods (E = 30000 ksi) support a load P= 7 kips. Each of the rods AB and CD has a 0.3-in?…

Q: coupling failure. Use G-83 GPa for stee 100 1.5 m 2 m

Q: 7000 N 7000 N 1m- -1m- 60° A B The cross-section of bar BC is rectangular with 40 mm width and 10 mm…

A: Draw FBD:

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

Q: The torsional assembly consists of solid 3.0 in. diameter aluminum [G= 4,000 ksi] segments (1) and…

Q: The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the…

A: We have to determine the value of maximum allowable magnitude of T if the working stress is 12 mpa…

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of…

A: Hooke's Law: It states that stress is directly proportional to strain within the elastic limit. It…

Q: Prob 1. A compound shaft consists of a solid aluminum shaft (BC) and a hollow steel tube (AB), with…

A: Data Given: τAllow-Alum = 6000 psiτAllow-Steel = 9000 psi Asked: Maximum external torque T that…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown.…

Q: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

A: Length of member LAB = 180 mm LBC = 120mm LCD = 100mm LDE = 100mm Diameter of steel (ds) = 40mm…

Q: The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB…

Q: The rigid bar Is pinned at A and held by two flexible bars at E and C. The load P Is appled at B.…

A: Given, Yield stress (σy) = 20 ksi Yield strain (e) = 0.001

Q: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

Q: 3) A - Steel The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod…

Q: The stepped steel shaft carries the torque T. maximum T. Determine the allowable magnitude of T if…

A: Here there are two limiting cases. one is for the angle of twist and one is for torsional shear…

Q: 3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and…

Q: The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly…

Q: The two wires are connected together at A. If the force P causes point A to be displaced…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

300 mm-
450 mm-
40 kN
A 1
B
30 mm
40 mm
40 kN
30 mm
The assembly consists of two red brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stain
less 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G.
The part ist fix at both ends (A, C and F)
Determine:
a. The reaction force at point A, C and F
b. The deflection of point B, E, D
c. The average normal stress developed in rods AB, CD and EF.
Brass C83400: E=101 GPa; G=37 GPa; oy=69 MPa; ou=241 MPa
Stainless steel 304: E= 193 GPa; G=75 GPa; oy=207 MPa; ou=517 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Time: 40 minutes Group -3 A copper rod ABCD of 800 mm cross-sectional area and 7.5 m long is subjected to forces as shown in Fig. B C P3 L2- L3 A D P1 + P2 + -P4 L1 Find the total elongation of the bar. Take E for the bar material as 100 GPa. P2 P3 P4 L1 L2 L3 P1 Name (kN) (kN) (kN) mm mm mm (kN) 40 30 20 50 3500 1500 2500 علي باقر عبد الزهرة جاسم
A copper rod ABCD of 800 mm cross-sectional area and 7.5 m long is subjected to forces as shown in Fig. B D P3 L2- L3 P1+ P2 -P4 L1 Find the total elongation of the bar. Take E for the bar material as 100 GPa. P2 P3 P4 L1 L2 L3 P1 Name (kN) (kN) (kN) mm mm mm (kN) 40 30 20 50 3500 1500 2500 علي باقر عبد الزهرة جاسم
* A For the RIGID beam shown, find the :deflection at point B 2m B 3m C 3m 50 kN ID +0.025 m O -0.025 m O Non of them O -0.125 m O +0.125 m O No deflection O
10 mm 5 KN-m 40 mm 5 KN-m 150 mm 15 mm 120 mm Determine (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at points H and K. State whether the normal stress is tension or compression. (c) the maximum bending stress produced in the cross section. State whether the stress is tension or compression.
3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
Q3: A rigid beam ABCD is supported as shown. Initially and at room temperature the beam is horizontal and carries no load. Calculate the force in the rods when the temperature of aluminum rod only is raised by 120°C. Steel Wire A= 50 mm Brass Rod E-200 Gpa L=2 m A= 300 mm E-83 Gpa L=2 m a = 12um/m C a = 19um/m C Gap-2mm Aluminum Rod A= 400 mm E= 70 Gpa L=3 m a = 23um/m C Im 1 m 1 m
The homogenous material wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L in mm in which portion BCD of the wire is horizontal in position. Determine the length L in mm in which portion AB of the wire is horizontal in position (meaning portion BCD is inclined) -80 mm- B IC 60 mm
What is the deflection at the hinge for the beam shown below? А C I В I L/2- - L/2
f. Calculate the maximum safe load "P" in KN Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Question 13 of 14 - /5 View Policies Current Attempt in Progress Determine the coordinates of the mass center of the welded assembly of uniform slender rods made from the same bar stock. a a 1.36 a Answers: (X, Y, Z) = ( i ) a i i ... II
Exercise 1 : Find the deflection at the point load and the slopes at the ends for the steel shaft which is simply supported at the bearing A and B as shown in Fig.1. Calculate the following: a. Deflection at the point load b. Slope at the ends - 1.25 x 10 mm 3000 N I2= 4x 10 mm B 150 mm 75 mm /- 125 mm Fig-() Take E-200 GPa. Given: Young's modulus, E = 200 GPa - 200 x 10 Pa (or) 200 x 10 N/m2 E - 200 x 10 N/m2 = 2x 10 N/mm2 Moment of inertin, Element i and 2, I, = 1.25 x 105 mm4 Element 3, 1, - 4 x 10 mm 3000 N my. : m2, 2 dyn. Fiy 150 mm da Fay d,3 Fay dye, Fay 125 mm t75 mm Fig. (i). For ciement 1, length L, = 150 mm For element 2, length L, - 75 mm For element 3, length L, = 125 mm Point load at node 2, F, =' 3000 N Fig.1