The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 3L 60° Answers: Ay= Dy= Dx = i i B 12 60° 60° E eTextbook and Media 1 1 I I L--- C 1L 30° L L L 1L D

The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 3L 60° Answers: Ay= Dy= Dx = i i B 12 60° 60° E eTextbook and Media 1 1 I I L--- C 1L 30° L L L 1L D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine magnitue, angle of the resultant force and location of it from E, considering the structural element having a seif weight of W KN/m (Where, W=1+3). Also calculate support reactions at A and E by using equilibrium equations. 40 kN 80 kN 50 LN te to E 3m 3m 5m 5m Fig-03 Hints: Self weight acts as uniformly distributed load throughout the length. While calculating moments, the action of total self-weight will be considered to be working right at the mid point of the beam.
A hatch door with a center of mass at G is supported by a cable. Identify the support reactions on the door. U 2m > 2 m Check all the possible support reactions on the door, even if some of them are equal to zero due to the loading given. Make sure the reactions in the set you choose do not depend on each other. B FBA at B along the rod A₂ M₁ MB By Az FAB at A along the rod FBC at B along the cable BC B₂
The elements of a wall-mounted swing-away stool are shown in the figure. The hinge pin P fits loosely through the frame tube, and the frame tube has a slight clearance between the supports A and B. Determine the reactions on the fram tube at A and B associated with the weight L of an 80 kg person. Also, calculate the changes in the horizontal reactions at C and D due to the same load L. St at e any assumptions. C P 65 mm A 175 mm B 65 mm D' 350 mm 85 mm
Problem: The elements of a wall-mounted swing-away stool are shown in the figure. The hinge-pin P fits loosely through the frame tube, and the frame tube has a slight clearance between the supports A and B. Determine the reactions on the frame tube at A and B associated with the weight L of an 80 kg person. Also, calculate the changes in the horizontal reactions at C and D due to the same load L. State any assumptions. 65 mm Al 175 mm B 65 mm D 350 mm 85 mm
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 1L 2L 3L D 4L 60⁰ A Answers: Ay= i Dy=i Dx= i B 60° 60° E 30⁰ L L L
The given bridge truss supports point loads of 200kN at joints B, D, F, H, and J. The structure is supported by pin support at the joint A and roller support at the joint I. Determine the member forces AD, CE, CF, FH, GI, and IJ. Indicate whether the forces are compression or tension. Show your calculation steps in detail and write your answers in the box below. 200 kN 200 kN 200 kN 200 kN 200 kN D F В E 7 m 4 m 3 m -5 m -5 m 5 m -5 m
Required information In the given figure, all pulleys are frictionless. Take the value of P to be 220 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P 0.5 ft P0.58 --20-20-20- Determine the reactions at point A and the force supported by the cable. (Do not include a minus sign in your response.) The horizontal component of the reaction force at A is lb →. The vertical component of the reaction force at A is The tension in the cable is lb. lb 1.
An L-shaped bar is supported by a bearing at A and a smooth horizontal surface at B. Take the value of Fto be 720 N. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1.5m 1.5m 2m Determine the reactions at A and B. (Do not include a minus sign in your response.) The y component of the reaction force at A is [ NT. The z component of the reaction force at A is N✓. The reaction moment at A about the y axis is N-m . The reaction moment at A about the z axis is N.m O The y component of the reaction force at Bis NT.
है A ★F B The structure shown above is in static equilibrium. The structure is made of square segments 1.5m on each side. Support A is a pin joint and support B is on rollers. An external force F=150.0 N is applied to the structure. What is the reaction force at B?
answer is B=14.528lb D= 14.58lb F= 3lb, but I need help to get to them 1. For the frame below a. Use a free body of the full structure to find the reactions at Pin A and Roller B. b. Determine the magnitude of the forces on pins B, D, and F. Show your ree oeY diagrams. 30 in-lb 10 lb 6" 7" 4" 3" 4" 3" 1. 1.25"
Problem Statement Based on Problem 6-69 from the textbook. Determine the reactions at supports A and B. a=6.3 ft b=11.Oft c=11.1ft d=7.8 ft Unique Values for Each Student: 500 lb/ft a a 700 lb/ft D
6KN 2. Find the support reactions at A and C. Using method of joints, determine the force in each member of the truss (shown to the left). Specify tension or compression for each member force. (Note: joint A is a pin and joint C is a roller.) Ans: Ar = 16 kN+, Ay = 9 kN 1↑, C = 16 kN →, FAB = 4 kN (T), FAD = 15 kN (T), FCD = 16 kN (C), FBD = 9 kN (C), FBE = 5 kN (T), A B. 3KN 0.9m %3D D %3D E FDE = 4 kN (C) 1.2m 1.2m