The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are ot = 40 MPa, oc = 80 MPa, and t = 12 MPa. w (kN/m) 75 mm :10 mm 10 mm- 150 mm 0.5 m 1 m 3 m 10 mm 150 mm

The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are ot = 40 MPa, oc = 80 MPa, and t = 12 MPa. w (kN/m) 75 mm :10 mm 10 mm- 150 mm 0.5 m 1 m 3 m 10 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that : E=200GN/m² E=70 GN/m² and a=11×10% per °C and a=22×10 per °C for Steel for Aluminum Alloy
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The assembly shown is made up of T-shape steel and two wood as shown. A bending moment M is applied to the composite beam. Given: Es = 200 GPa Ew = 25 GPa M = 90 kN.M h = 200 mm c. Calculate the absolute maximum stress in the steel in MPa. d. Calculate the stress in the steel along the top edge in MPa.
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.
Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa