Hi, I need help with this dynamics question. Thank you The circular cam of radius R = 16 mm is pivoted at O, thus producing an eccentricity of 2. Thefollower A sitting on the cam can only move in the vertical direction. For the shown geometry, therelationship between x, the vertical position coordinate of the follower A, and the angle is:x(0)R=2 (cos 0 +√√cos²0 + 3)When 0 = 45the cam is rotating clockwise about O with the angular speed = 2000 rev/min, which isdecreasing at a rate of 2 rad/s². For this moment, determine:the velocity of the follower A; andthe acceleration of the follower Aa)b)

Answered: Image /qna-images/answer/b8447af8-7c00-430b-bb11-b60a668670a8.jpg

Answered: The circular cam of radius R = 16 mm is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Analytically determine the linear displacement of the piston in the compressor linkage shown in the figure as the 45 mm. crank is rotated from its current position 90 degree clockwise.
A follower starts from a dwell and accelerates up to a velocity of 25 cm/s at the end of a half cycloidal segment. If the lift L is 8 cm and the angle B is 75 degrees, find the cam's speed.
The crank-rocker mechanism shown has lengths n = 9 in, r2 = 2 in, r3 = 7 in, andr4= 10 in. Find the angular displacement Aa that crank OA makes to move the rocker OpB from the extreme right to the extreme left position. Crank OAA rotates counterclockwise as shown. Write your answer in degrees but do not write the units. B A 0B Answer. DELL
3.7 Fig. 3-8 shows a cam mechanism. AB = 1, the radium of the cam is R,OA = h, OAB = 90°, the angle velocity of the cam is w, determine the angle velocity and angle acceleration of the follower 2. B, 2. Fig. 3-8
For the circular cam in the posture shown, the angular velocity of the cam is w2 = 15 rad/s ccw. There is rolling contact between the cam and the roller, link 3. Find the angular velocity of the oscillating follower, link 4. 3.29 'R E 3 4 3" 2"R 135° A 3" Figure P3.29 1/2
A cam has the following characteristics: (a) It starts from dwell and ends in another dwell (b) In section I the cam has a parabolic profile: Y = Ay² + BY + C (c) In section I from 0 < y < 1/2 the cam rises to the height of ½ (d) In section Il the cam has a cubic profile: Y = Dy³ + Ey² + Fy + G (e) In section Il from 1/2 < y < 1 the cam rises to the height of 1 Write the non-dimensional boundary conditions for each section of the CAM but do not derive for the displacement equations
As shown in the figure below, the wheel rolls on the plane with constant angular velocity w = 1.3 O rad/sec. The plane J on which the wheel rolls is not fixed to the reference frame but instead translates on the reference frame G at constant velocity V = 2.9 ft/sec to the left. Find Vo (the magnitude of the velocity at the point Q). 1 P 1.6 ft J V Figure is from "Engineering Mechanic An Introduction to Dynamics", McGill and King.
Consi der a circular cam with a flat face follower as shown in the figure below. The cam is rotated in the plane of the paper about point P lying 5 mm away from its center. The radius of the cam is 20 mm. The distance (in mm) between the highest and the lowest positions of the flat face follower is 5 mm
The inverted crank-slider shown has crank AB 3 in and ground link AC = 6 in. Find the re-rocking angle AO, of rod 4 between its extreme right and extreme left positions. Write your answer in degrees but do not write the units. A C DELL
Determine the velocity of rod R for 0 = T/2 rad in the cam Cif the cam rotates with a constant angular velocity w = 10 rad/s. The pin connection at o does not cause an interference with the motion of A on C. Enter the velocity of R in m/s in the box below. Assume positive to the left, as shown in the figure. ri =1 m, r2 = 0.15 m. Enter the answer in m/s in the box below. C
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a
PLANETARY GEARS KINEMATCS The gear is connected to Rack C in the picture shown below. The rope B is attached to the gear at point A. If the velocity of the rope and rack are as shown in the figure below, then what is the velocity and acceleration of point O? What is the angular velocity and angular acceleration of the gear? ay = 1.5 m/s? vn = 3 m/s 0.3 m -0.2 m ac = 0.75 m/s? Ve: = 1.5 m/s

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS