The d-diagram for a collagen fiber bundle from which a human tendon is composed is shown. If a segment of the Achilles tendon at A has a length of 6.5 in. and an approximate cross-sectional area of 0.229 in², determine its elongation if the foot supports a load of 125 lb, which causes a tension in the tendon of 343.75 lb. (ksi) 4.50 3.75 3.00 2.25 1.50 0.75 0.05 0.10 150b (in./in.)

The d-diagram for a collagen fiber bundle from which a human tendon is composed is shown. If a segment of the Achilles tendon at A has a length of 6.5 in. and an approximate cross-sectional area of 0.229 in², determine its elongation if the foot supports a load of 125 lb, which causes a tension in the tendon of 343.75 lb. (ksi) 4.50 3.75 3.00 2.25 1.50 0.75 0.05 0.10 150b (in./in.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D
A 90 degrees angle on a 1/2 inch water pvc pipe. determine the force on the angled pipe if the water prusser is 30kpa.
Determine the magnitude of the force which member CD exerts on the pin at C. 300 N B 0.58 m 0.58 m 0.80 m 0.80 m |21% 21 A D Answer: CD = i
1. Compute the force in each member. 2000LB 3000LB В 60° 60° E A 60 607 REH 10' 10' RA 4000LB Rev
1:39 م SuperNe l. A sulms.su.edu.om P Flag question Member ABC is supported by pin support at B and by cables attached at A and C and passing over a frictionless pulley at D. Determine the tension force in the cable AD if the tension force in the cable CD is 75 N. 160 mm C a = 120 mm 250 mm A 75 N Вeer,2013 Select one: Оа. 100 N O b. 75 N Ос.0 O d. 80 N
Q2. Determine the young's modulus of elasticity from the following test result on a steel rod: Rod diameter = 25 mm Rod length Maximum applied load = 300kN = 150mm Rod extension after test = 10mm
Determine the force in each cable needed to support the weight of mini extruder (2000 N) on the platform. 2000 N 6 m 15 m 3m. 75m_
Q.2 The forces in the member BC and BD respectively are 2m D 2m 2m 2m 10KN A 2m 20 A V3 (Tensile) and v3 (Tensile) 10 10 10 v3 (Tensile) and v3 (Compressive) WRONG 10 10 V3 (Compressive) and v3 (Tensile) 10 20 v3 (Compressive) and v3 (Tensile)
A power transmission cable consists of eighteen copper wires each of 2 mm diameter surrounding four steel wires each of 3 mm diameter. Determine the extension of a 30 m length of the cable when it is being laid with a tension of 6 kN. For steel, Estee 200 GN/m2; for copper, Ecopper= 100 GN/m2.
A steel tape is 30 m. long under a standard pull of 6 kg. with a constant cross-sectional area of 0.05 cm?. if the normal tension applied to make the tape equal to its nominal length when supported only at the end points that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 16 kg. Determine the unit weight of the tape. Modulus of elasticity of the tape is 2x10^6 kg/cm^2
Question 4 4. A string has a diameter of 1 cm and the original length of 2 m. The string is pulled by a force of 200 N. Determine the change in length of the string! Young's modulus of the string = 5 x 109 N/m2.
is The left support of the cable shown in Fig. located 40 ft below the right support. The cable is horizontal at the left support. If the maximum tension in the cable re- sulting from a uniformly distributed load w along the hor- izontal is 400 kip, determine the length of cable 40 n 400 ft