"The diagram below illustrates a bridge rectifier circuit connected to an ideal transformer with center-tapped windings. Assume that the diodes are ideal. • Plot the instantaneous voltage and current waveforms for the loads R₁ (292) and R₂ (292), with reference to the center tap of the transformer. • Briefly comment on where this rectifier may be used. Turns ratio -10 240V, 50Hz D1 D4 D3 Дог R=202 R: 202

"The diagram below illustrates a bridge rectifier circuit connected to an ideal transformer with center-tapped windings. Assume that the diodes are ideal. • Plot the instantaneous voltage and current waveforms for the loads R₁ (292) and R₂ (292), with reference to the center tap of the transformer. • Briefly comment on where this rectifier may be used. Turns ratio -10 240V, 50Hz D1 D4 D3 Дог R=202 R: 202

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Full Wave Rectifier Circuit The circuit of the full-wave rectifier can be constructed in two ways. The first method uses a centre tapped transformer and two diodes. This arrangement is known as a centre tapped full-wave rectifier. The second method uses a standard transformer with four diodes arranged as a bridge. This is known as a bridge rectifier. Advantages of Full Wave Rectifier The rectification efficiency of full wave rectifiers is double that of half wave rectifiers. The efficiency of half wave rectifiers is 40.6% while the rectification efficiency of full wave rectifiers is 81.2%. The ripple factor in full wave rectifiers is low hence a simple filter is required. The value of ripple factor in full wave rectifier is 0.482 while in half wave rectifier it is about 1.21. The output voltage and the output power obtained in full wave rectifiers are higher than that obtained using half wave rectifiers. Question: What is the main disadvantage of a conventional full-wave…
1) How is the diode and zener diode in the electronic circuit and how they work?indicate the differences between them.2) Can a zener diode be used instead of a regular diode? please explain.3) Is it to step down and rectify the 220V AC signal by means of a transformer or to convert 220 V?rectify it and then reduce its value to the desired DC level using a voltage divider circuit?suitable.?4) Bridge type full wave rectification with two diodes full wave rectification using a medium ended transformerCompare the rectifier circuit and list its advantages and disadvantages relative to each other.5) What is the concept of PIV (Peak Inverse Voltage) for rectifier circuits?For which rectifier circuits is this value more important?
92) For three - phase half-wave Controlleed rectifier Shown in he figure: 1. Derive a fomu la for mean load Voltage. 2. praw the wave form of vo, i,,i, iy and voltage across thyristor 1 (r.) assuming highly inductive load and d = 120
In a centre-tapped full wave rectifier having a load resistance resistance equals 3 2. The turn's ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS ), 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency. 750 52 diode forward bias
The primary winding to secondary winding turns ratio of a centre-tapped transformer is 5:1. The primary winding of the transformer is fed from 220V ac supply and the secondary voltage is connected to a single phase full wave rectifier which consist of two diodes. The forward resistance of each diode is 50 and load resistance is 250. Determine the following: A. peak value of current B. de load current C. rms value of load current D. de power E. ac power input to rectifier F. efficiency of rectifier
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110v/11-0-11 V is used with R1-1 Kn. Assume diode as Germanium. a) Find Input Voltage D, Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. eelee
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
The turn-ratio of the transformer ( N1 / N2 ) = ? / The PIV rating for diodes , PIV = ? / The Average diode Current IDavg = ?
Figure Q1 (a) showed full wave rectifier. The step-down transformer has turn ration 9:1. Cut in voltage for diode is 0.7V, and RĻ = 100 Q. Calculate the following: (i) Output load voltage, Vo. (ii) Average output voltage Vo(de), and average load current, lo(de) (iii) Peak reverse voltage, PIV. (iv) Draw the output waveform. 9:1 A D, 115V 60HZ D.C. R O/P B Figure Q1(a)