The drag force acting on a model torpedo, 1/20 the size of the prototype, is measured at 80 N in water with density of 988 kg/m³, and kinematic viscosity of 0.56 × 10-6 m² /s. The prototype's speed is 15 m/s in sea water with density of is 1010 kg/m³, and kinematic viscosity of 1.3 × 10-6 m² /s. Determine the drag force acting on the prototype.

The drag force acting on a model torpedo, 1/20 the size of the prototype, is measured at 80 N in water with density of 988 kg/m³, and kinematic viscosity of 0.56 × 10-6 m² /s. The prototype's speed is 15 m/s in sea water with density of is 1010 kg/m³, and kinematic viscosity of 1.3 × 10-6 m² /s. Determine the drag force acting on the prototype.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We want to predict the drag force on a remote-control airplane as it flies through air having a density of 1.21 kg/m³ and a viscosity of 1.76x10- Pa-s. The airplane's fuselage has a diameter of 200 mm and the airplane will fly through air at a speed of 32 m/s. A model of the airplane's fuselage will be tested in a pressurized wind tunnel. The diameter of the model is 75 mm and the density and viscosity of the air in the wind tunnel are 3.00 kg/m³ and 1.82× 10-5 Pa-s, respectively. a) The diameter of the airplane's fuselage will be used to define the Reynolds number Re, for the flow around the fuselage. Compute the Reynolds number for the flow around the airplane's fuselage (answer: Re, = 4.40x 10'). b) Find the speed of the air that should be used to test a model of the fuselage in the wind tunnel to correctly model dynamic conditions (answer: 35.6 m/s). c) The model is tested in the wind tunnel at four speeds that bracket the speed computed above. The measured drag forces on the…
1. The Stokes-Oseen formula for drag force Fon a sphere of diameter D in a fluid stream of low velocity V, density p, and viscosity u is: 9T F = 3TuDV + 16PD? Is this formula dimensionally homogenous? 2. The efficiency n of a pump is defined as the (dimensionless) ratio of the power required to drive a pump: QAp input power Where Q is the volume rate of flow and Ap is the pressure rise produced by the pump. Suppose that a certain pump develops a pressure of Ibf/in? (1ft = 12 in) when its flow rate is 40 L/s (1L =0.001 m). If the input power is 16hp (1hp = 760 W), what is the efficiency?
Consider a Falling Sphere Viscometer, which is used to measure the viscosity μ of a fluid by observing the terminal velocity of a heavy sphere (density Ps and diameter D) falling under gravity in a column of the fluid (density pf). (a) Use Dimensional Analysis to derive a formula for the drag force exerted on the sphere by the viscous fluid when it is moving at speed v through the fluid. (b) How is the terminal velocity of the sphere related to the fluid viscosity? (c) If the sphere starts from rest, use Dimensional Analysis to predict the timescale over which the sphere will reach its terminal velocity. Please use dimensiona analysis to solve the problem Answr for part a= Fd=KmuVD answer for part b=V=Fd/kmuD Please solve only for part C (part a and b no need to solve)and expalin in detail Thanks
A 500 ft long ship is to operate at a speed of 20 mph in ocean water whoseviscosity is 1.2 cP and specific weight is 64 lb/ft. What should be thekinematic viscosity of the liquid used with a 10-ft-long model of this ship sothat both the Reynolds number and the Froude number would be the same?Does such a liquid exist?
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
A student needs to measure the drag on a prototype of characteristic length d, moving at velocity U, in air at sea-level conditions. She constructs a model of characteristic length dm such that the ratio d,/dm drag under dynamically similar conditions in sea-level air. The student claims that the drag force on the prototype will be = a factor f. She then measures the model identical to that of the model. Is her claim correct? Explain, showing your work (no credit for just guessing).
The drag force on a submarine, which is moving on the surface, is to be determined by a test on a model which is scaled down to one-twentieth of the prototype. The test is to be carried in a towing tank, where the model submarine is moved along a channel of liquid. The density and the kinematic viscosity of the seawater are 1010 kg/m³ and 1.3x10-6 m 2/s, respectively. The speed of the prototype is 2.6 m/s. Assume that F = f(V, L. g. p.), using pi-theorem and similarity principle to: a) Determine the speed at which the model should be moved in the towing tank. b) Determine the kinematic viscosity of the liquid that should be used in the towing tank.
The Stokes-Oseen formula for drag force F on a sphere of diameter D in a fluid stream of low velocity V, density p, and viscosity µ is 97 F= 3ημDV+ ΡD Is this formula dimensionally homogeneous?
Algebraic equations such as Bernoulli's relation, are dimensionally consistent, but what about differential equations? Consider, for example, the boundary-layer x-momentum equation, first derived by Ludwig Prandtl in 1904: ди ди ap ат ри — + pu Әх + pg: + дх ày ду where T is the boundary-layer shear stress and g, is the com- ponent of gravity in the x direction. Is this equation dimen- sionally consistent? Can you draw a general conclusion?
A fighter aircraft is to operate at 200 m/s in air at standard conditions ( = 1.2 kg/m3). Amodel is constructed to 1/20 scale (length ratio) and tested in a wind tunnel at the sameair temperature (same air viscosity) to determine the drag force. The drag force FD is afunction of the air density  and viscosity , the velocity V and the cross section length ofthe airplane D.
An automobile has a characteristic length and area of 8 ft and 60 ft2, respectively. When tested in sea-level standard air, it has measured velocities of 20, 40, and 60 mi/h and drag forces of 31, 115, and 249 lbf, respectively. The same car travels in Colorado at 115 mi/h at an altitude of 3500 m. Using dimensional analysis, estimate its drag force (in lbf). Using dimensional analysis, estimate the horsepower required to overcome air drag (in hp)