The following three phase inverter in Figure 1 below is supplied by a DC voltage of Vpc = 1000V and connected to the star connection of resistive load, R=60n. The load frequency is 50Hz. Assume that three switches are conducted at each interval. State the sequence number of conducting transistor for each interval and illustrate the equivalent circuit connection of load for each interval. Based on the equivalent circuit connection of load, determine the value of line voltage Vry and value of phase voltage VrN- Provide your answers in Table 1. (C3,CLO1)

The following three phase inverter in Figure 1 below is supplied by a DC voltage of Vpc = 1000V and connected to the star connection of resistive load, R=60n. The load frequency is 50Hz. Assume that three switches are conducted at each interval. State the sequence number of conducting transistor for each interval and illustrate the equivalent circuit connection of load for each interval. Based on the equivalent circuit connection of load, determine the value of line voltage Vry and value of phase voltage VrN- Provide your answers in Table 1. (C3,CLO1)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

QUESTION SEVEN A single-phase bridge inverter is fed from 230 V dc. In the output voltage wave, only fundamental component of voltage is considered. Determine the rms current ratings of an SCR and the diode of the bridge for the following types of loads: (a) R = 20 (b) wL = 29. Find also the repetitive peak voltage that may appear across a thyristor in parts (a) and (b).
3. A three-phase inverter is connected to a balanced star-connected resistive load with RL = 180 and a 500V d.c. supply. The inverter frequency is 100HZ. a) Calculate the current, voltage and power for 120 degree conduction periods. b) Calculate the current, voltage and power for 180 degree conduction periods. R. A ww R. B is R. ww of of to
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
single phase half bridge inverter has load r=2ohm and dc souuce voltage vs/2=115v . calculate THD and HF
For single phase voltage source bridge inverter: 1- Draw th circuit. 2- With R=102, L=50mH, frequency is 50 Hz and supply voltage is 400V and square wave output, draw the waveforms of vo and io. 3- Calculate the RMS value of output voltage and mean output power.
Q1- For single phase voltage source bridge inverter: 1- Draw the circuit. 2- With R=102 , L=50mH, frequency is 50 Hz , supply voltage is 450V and quasi-square wave output and a 50 percent on time, draw the waveforms of output voltage (VL.) and load current (iL) when I=25.05A , Io= -9.217A. 3- Calculate the RMS value of output voltage and mean output power.
Show that the THD of the phase voltage of the three-phase inverter square-wave mode is 0.31
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
A three phase bridge inverter is fed from a 500 V dc source. The inverter is operated in 180° conduction mode and it is supplying a purely resistive, star-connected load. The RMS value of the output (line) voltage is
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
For single phase voltage source bridge inverter 1. Draw the circuit. 2 With R 100. I SOmH frequency is 50 Hz and supply voltage is 380V. With square wave output draw the waveforms of output voltage v1 and load current i . 3 Calculate the RMS value of output voltage and mean output power.