The geometry and reinforcement configuration of the column is given below. The material properties are CX/ S420. The analysis results due to different loading combinations are as follows (C30,b-400mm,h%3D600mm) Combo 1: Nd%3D1250 kN / Mdx = 250 kN !! Combo 2: Nd%3D1000 kN / Mdx = 400 kN Combo 2: Nd%3D750 kN/ Mdx = 550 kN Determine the longitudinal reinforcement of the column.

The geometry and reinforcement configuration of the column is given below. The material properties are CX/ S420. The analysis results due to different loading combinations are as follows (C30,b-400mm,h%3D600mm) Combo 1: Nd%3D1250 kN / Mdx = 250 kN !! Combo 2: Nd%3D1000 kN / Mdx = 400 kN Combo 2: Nd%3D750 kN/ Mdx = 550 kN Determine the longitudinal reinforcement of the column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 Considering flexural buckling, determine the allowable and design compressive strength using L = 5m (A = 6,265mm2, rx = 106.43mm, ry = 49.28mm %3D %3D W10× 33 L A992 steel
FOR THE GIVEN PROPERTIES DESIGN d': 15 mm THE REINFORCEMENT OF : 400 mm b d = $80 mm fc = 33 MPa fy = 320 MPa Mu: 1 000 000 000 N mm A. USE B.USE OF NSCP 2001 NSCP 2015 BEAM THE BEAM 132 13 Gra mm of BELOW. #H 1606 210135 03 M 12437 P0122399/100mA 02338941 242
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
(1) (2) steel stress-strain Curve Es= Esteel = what is f db #3 #4 #5 #6 #7 #8 #9 #10 ksi 0.005 Ab FOR Grade 60 steel. E Ey = when fs = 45 ksi lbs/ft_ when Es=0.005
Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending momen of 565 N.m to 1130 N-m as the axial load varies from 4500 N to 13 500 N. Determine the required diameter of the rod for a factor of safety 2. Neglect any stress concentration and column effect. Assume the following values: Ultimate strength = 550 MPa Yield strength = 470 MPa Size factor = 0.85 %3D Surface finish factor = 0.89 Correction factors = 1.0 for bending = 0.7 for axial load The endurance limit in reversed bending may be taken as one-half the ultimate strength.
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
*4-36. The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red brass C83400 end segments DA and CB. Determine the average normal stress in each segment due to the applied load. Esteel l = 200 x10 Pa. EBrass = 101 K109h. |-250 mm-- 500 mm -250 mm- 50 mm 20 mm 75 kN 100 kN D A 75 kN 100 kN В C
Using the stress block, determine the ultimate moment of resistance of the section shown in Figure 2 and check whether the steei provided satisfies the bending moment due to the loads on the beam. Characteristic compressive strength of concrete, fck= 25 N/mm² Characteristic tensile strength of steel, fyk = 500 N/mm2 Clear cover to main steel as 20 mm. Ultimate Design Load =13 kN/m 2 402 mm 370 mm 2 1470 mm 9 m 230 mm Figure 2
A reinforced concrete T – beam is to be designed for tension reinforcement only. The beam width is 250 mm and the effective depth is 400 mm. The flange thickness is 100 mm and its effective flange width is 900 mm. The applied moment is 300 kN–m. What is the area of tension reinforcement required? use: fc’ = 20.7 MPa and Fy = 414 MPa. * a. 3 983 mm² b. 5 105 mm² c. 2 166 mm² d. 4 094 mm²
O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
Estimate for the concrete, formworks, reinforcement requirement of Beam GG-36. Length of Beam 1 = 8200mm Length of Beam 2 = 8200mm Size of Column = 800mm x 800mm GG-36 IGG-36 GG-131 009*00t GB-4 009*00+ GG-1