The image below shows a beam subject to two couples, F₁ = 670 N and F₂ = 760 N. (Figure 4) The dimensions are 2₁ =1.40 m, z₂ = 1.10 m, h=0.12 m, 0 = 50°, and = 28°. What is the net moment on the beam due to the two couples? Express your answer to three significant figures and Include the appropriate units.

The image below shows a beam subject to two couples, F₁ = 670 N and F₂ = 760 N. (Figure 4) The dimensions are 2₁ =1.40 m, z₂ = 1.10 m, h=0.12 m, 0 = 50°, and = 28°. What is the net moment on the beam due to the two couples? Express your answer to three significant figures and Include the appropriate units.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniform beam, 1.5 metre long, is suspended in a horizontal position by two vertical support rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with Esteel = 210 GPa. Rod B has a diameter of 16 mm and is made from copper with Ecopper = 105 GPa. This simply supported beam is to carry a motor vehicle engine and gearbox weighing 5,5 kN. Determine the distance 'x' from the left-hand support 'A' in order for the beam to remain in a horizontal position. !Calculate the stress in each rod due to the applied load. Calculate the movement (extension) of the support wires under this 10 kN load. Will the rods be able to withstand the applied load? Motivate your answer. 500 mm 300 mm A B 5.5 kN 1500 mm
In the figure below , A, B , and C are all pin-connected , while D and E are fixed. With x = 11.6 what is the horizontal support reaction (in kips or k units) at C? Approximate final answers up to two decimal places.
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-
A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following unknowns if the modulus of elasticity is 160GPa and the maximum deflection is -0.63254616477273mm. BEAM'S DIMENSION: Width = 110mm , Height = 480mm NOTE: L = 3m Solve the maximum moment of the beam. Answer for part 1 kN-m Determine the shear at midspan.
In the figure below A B and C are all pin connected while D and E are fixed. with x = 5.9 what is the vertical support reaction (in kips or k units) at A? Approximately final answers up to two decimal places.
1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is represented by the 2 kN load shown. a. Produce shear and moment diagrams for the supporting frame ABC. b. Calculate the horizontal deflection of the point of loading. Assume that frame ABC has bending stiffness El = 2.7×105 Nm². 0.9 m A 0.6 m C B 2 KN
A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1200 kN and factored moment of 280 kNm. Using the interactiondiagram, determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
Draw the shear-force and bending-moment diagrams for the beam shown. Determine the bending moment 3.07 ft to the right of point A if P = 3.41 kips and Q = 4.9 kips. Round off the final answer (in lb ft) to two decimal places. ... y P D X C A 2 ft 93 B 6 ft - 4 ft →
A beam is loaded as shown in the figure . 1. Determine the maximum negative moment. 2. Determine the maximum positive moment.
Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the right of the 2-kip load. Follow the sign convention. Figure -6 ft D -6 ft W B 4 ft E 4 ft 1 of 1 > C Determine the normal force at point D. Express your answer in kilopounds to three significant figures. ND = Submit Part B V|| ΑΣΦ ↓↑ vec 5 VD= Request Answer Determine the shear force at point D. Express your answer in kilopounds to three significant figures. ——| ΑΣΦ ↓↑ vec ? ? kip kip
Q2: Determine the moment of the (50 N) force shown in figure with respect to: 1-Point A, 50 N 2 т 30° 2-Point O A 3. 60°
A beam is subjected to pure torque, and its cross-section is shown in the figure. fy = 2800 kgf/cm^2, fc' = 280 kgf/cm^2. Both closed stirrups and longitudinal reinforcements are #4 steel bars, and the distance between closed stirrups is 15 cm and the net cover is 4 cm. The beam section is subjected to a design torque Tu = 3.0 tf - m. The strength reduction factor o is 0.75, Questions (1) Is the cross-section size of this beam appropriate? (2) Is the arrangement of torsional reinforcement in this beam section appropriate? #4 Rebar (db=1.27 cm, Ab-1.267 cm^2).