The inside design conditions for a conditional space are 19.5 degree C dry-bulb and 17.8 degree C wet-bulb. The outside air is at 31.5 degree C dry-bulb and 26.7 degree C wet bulb. The dry bulb temperature of the air entering the space is 12.5 degree C. The apparatus dew point is 10.0 degree C. Air leaves the conditioner saturated. What is most nearly the system bypass ratio? A. 0.11 B. 0.26 C. 0.35 D. 0.48

The inside design conditions for a conditional space are 19.5 degree C dry-bulb and 17.8 degree C wet-bulb. The outside air is at 31.5 degree C dry-bulb and 26.7 degree C wet bulb. The dry bulb temperature of the air entering the space is 12.5 degree C. The apparatus dew point is 10.0 degree C. Air leaves the conditioner saturated. What is most nearly the system bypass ratio? A. 0.11 B. 0.26 C. 0.35 D. 0.48

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter10: System Charging

Section: Chapter Questions

Problem 16RQ: A technician takes the following readings on an R-404A refrigeration system: Head pressure = 205...

See similar textbooks

Similar questions

which are the following statement is true? * [ coP of Camot refrigeration cycle does not depend on the working fluid GOP of Gamt cycle is the higher than any other refrigeration cycles. in all fresh air system, the cooling capacity of the space is approximately equal to the O 0 spacecoiingload o The dual pipe water distribution system recommended for fast controlling of air temperature and relative humidity in space.
A technician takes the following readings on an R-404A refrigeration system: Head pressure = 205 psig Suction pressure = 30 psig Condenser outlet temperature = 80F Evaporator outlet temperature = 10F Using the pressure/temperature chart in Figure 10.25, find the condenser subcooling and evaporator superheat amounts.
What is the difference between an even and an uneven parallel compressor system?
What advantage does a capillary tube have over a thermostatic expansion valve?
Is air conditioner an open or closed system?
Air conditioner using R-22 works on the condensing evaporating pressures of 99.36 psia and 19.62 respectively. The nv is equal to ( 60%) if m= 4% , Tcy= 20 F, y=1.3 and Ap= 1.2. True O False
A. Using the steam tables, determine the amount of coolimg water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47% moisture, mass flow rate= 7200 + (100/25) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: ___ B. Draw the schematic diagram if the condeser and process in the PV and TS diagram. Cp H2O= 4.187 KJ/(kg-K)
Draw a neat diagram and explain the working principle of a two-stage reciprocating air compressor?
Question#1 Pressure-enthalpy chart is another method to obtain an initial performance estimation of refrigeration/heat pump cycles used in heating, ventilation and air-conditioning (HVAC) system. Your role is to provide design and installation services for air -conditioning (AC) system a preliminary performance estimation. Given the following design specifications: Refrigerant HFC-134a as the working fluid - Ideal cycle operation condition is assumed - Cycle is operated at high pressure line of 0.8 MPa - Cycle is operated at low temperature line of – 10° C Flow rate is 0.1 kg/sec The head of the department in the company that you are working in asked you to make use of pressure -enthalpy chart provided for HFC-134a refrigerant Task.1 1. Determine the Refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR) and their corresponding rate/power values in kW.
Question#1 Pressure-enthalpy chart is another method to obtain an initial performance estimation of refrigeration/heat pump cycles used in heating, ventilation and air-conditioning (HVAC) system. Your role is to provide design and installation services for air -conditioning (AC) system a preliminary performance estimation. Given the following design specifications: Refrigerant HFC-134a as the working fluid - Ideal cycle operation condition is assumed - Cycle is operated at high pressure line of 0.8 MPa Cycle is operated at low temperature line of – 10° C Flow rate is 0.1 kg/sec The head of the department in the company that you are working in asked you to make use of pressure -enthalpy chart provided for HFC-134a refrigerant Task.1 2. Estimate the COPR 3. Determine the low-pressure line value.
High- temperature source Generator Condenser 3+ Expansion valve Valve Pump Absorber Evaporator Refrigerated region Cooling water In the absorption refrigeration cycle, which of the follov the compressor in the vapor-compression cycle? componennts replace absorber, pump & generator condenser, expansion valve & evaporator generator, condenser & expansion valve condenser, generator & pump evaporator, absorber & pump expansion valve, evaporator & absorber Weak solution Strong solution
Help provide a mathematical model of each of the air conditioning components of the system and the key equations describing their performance. -Precooler -Primary Heat Exchanger -Flow Control Valve -Compressor