The lap joint shown is fastened by 6 – 20mm diameter rivets. Assuming that P = 200KN, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6 rivets, and the diameter of hole is 22mm. See figure 102. %3D

The lap joint shown is fastened by 6 – 20mm diameter rivets. Assuming that P = 200KN, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6 rivets, and the diameter of hole is 22mm. See figure 102. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress t= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09
In the hanger shown in figure 2, the upper portion of link ABC is 3/8 in. thick and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/8-in. diameter while a 1/4-in.-diameter pin is used at C. Determine: the average shearing stress on the bonded surfaces at B. the bearing stress in the link at C. Figure 2 1.75 in.- 6 in. 7 in. E 500 lb B 5 in. D -1.25 in. 10 in.
Solve the following problem of a steel tensile plate with a concentrated load applied at the top, as shown below. Determine at what depth the effect of the load dies out. Plot stress oy versus distance from the load. At distances of 1 in., 2 in., 4 in., 6 in., 10 in., 15 in., 20 in., and 30 in. from the load, list oy versus these distances. Let the width of the plate be b = 4 in., thickness of the plate be t = 0.25 in., and length be in. Look up the concept of St. Venant's principle to see how it explains the stress behavior in this problem. L P = 1000 lb NUMI - E бу bt Oy bt 6 Gy = = P bt
For the lap joint shown in figure. 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa. 2. Determine the safe load P which may be applied if the bearing stress of the plate is limited to 110 MPa. 3.Determine the safe load P if the average tensile stress of the plate is limited to 140 MPa.
2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N compressive load on the link. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile stress allowed in the material is 30MPa. Calculate the safe load the stud can carry.
ear Solve the problems below: 1. The lap joint shown in Fig. P-126 is fastened by four 3/4 -in.- diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 16 ksi and the bearing stress in the plates is limited to 20 ksi. Assume the applied load is uniformly distributed among the four rivets. 4. 4 in 7/8 in 718 in 40 kN
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm2 . Take the permissible tensile stress as 35 MPa.
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]